AT&T Partner Plus Скачать руководство пользователя страница 30

Страница: 30 / 87

Dial Mode

Code:

#201

Description:

Identifies each outside line as either touch-tone or rotary.

Valid Entries:

✓

Touch-tone line

2 = Rotary line

Considerations:

If you are using touch-tone phones on rotary lines, you may

need to adjust the Rotary Dialing Timeout (#108).

Programming Steps:

Press [ Feature ] [ 0 ] [ 0 ] [ System Program ] [ System Program ] [ # ] [ 2 ] [ 0 ] [ 1 ] . The

display reads:

Dial Mode

Line:

2. Enter the first line to be programmed. For example, to program line 8,

press [ 8 ] . The display reads:

Dial Mode L8

1 Touch Tone

3. To change the dial mode, press [ Next Data ] . The display reads:

Dial Mode L8

2 Rotary

To program another line, press [Next Item] or [ Prev Item ] until the correct line number shows
on the display. Follow step 3 to change the dialing mode. Repeat for all lines that you
want to change.

✓

= Factory Setting

To go to the next procedure: [ Next Proc ]

To go to a specific procedure: [ # ] [ 2 ] [ 0 ] [ 1 ] . The

To go to the previous procedure: [ Prev Proc ]

(where XXX is the procedure number)

To return data to the factory setting: [ Remove ]

To exit system programming: [

Feature ] [ 0 ] [ 0 ]

System Programming 3-9

Содержание Partner Plus
























































































Результаты поиска

Содержание Partner Plus

Отзывы:

AT&T Partner Plus, Инструкция по установке и программированию, Страница: 30 / 87

Результаты поиска

Содержание Partner Plus

Отзывы: