ATAGO PAL- HIKARi 51 Скачать руководство пользователя страница 1

QR code

Introduction

Measurement tips and precautions

Replacing the Batteries

Error Meassages

Thank you for purchasing the instrument.

Read and follow all safety instructions before 

operating the instrument. 

Fairure to comply with the following instructions may 

result in personal injury or property damages.

This instrument measures amount of light absorbed by 

shining the near infared light to the sample then 

converts to Brix (sugar level) to display.

Brix (sugar level) can be measured with no need to cut 

and squeeze the samples. 

Measurment variance may be seen depending on the 

variety and harvest timing. This instrument is equipped 

with offset function to match the value in such cases. 

Press the 

side button

Press against a sample, 

then press the side button.

The measurements are displayed.

Depending on the variety, there may be a difference between the refractometer 

(sugar meter) and the measured value. Please confirm the difference from the value 

measured with your refractometer (PAL - 0 of the set when purchasing IR Brix Meter 

x Brix Meter) and use the offset function as necessary. (Refer to “Offset Function” ) 

LCD Auto Shut-off

The instrument will turn itself off 

after 30 seconds of inactivity. 

To manually turn it off, hold down 

the START button for more than 

3 seconds.

The temperature difference between the 

surface and the inside of the sample, and 

temperature difference between this 

instrument and the sample may affect the 

measurement values.

Especially when measuring refrigerated 

samples, be sure to let the samples 

acclimate to the ambient temperature.

The instrument may not measure correctly 

when there is water droplets, dust or scar, 

and bruising soft spots.

Be sure to avoid any spacing between the 

sample and the outer cushion to avoid the 

external light interference. If the cushion is 

deteriorated, please replace it with a brand 

new cushion. (Refer to “How to change the 

cushion”)

Example for measurement value: Take few 

measurements from the same sample, 

then compute and use the average.

Acclimate the sample and this 

instrument to ambient temperature.

Place the sample on the Cushion RS 
Triple.
Make sure that the sample and the 
Cushion RS Triple seal properly.

Peel corn husk.

● 

Clean the surface of the samples. 

   Do not measure the spoiled spots.

● 

Place the sample stage to the sample.

● 

Sugar level varies depending on 

the measured area.

When there is an operation error or malfunction, the 

below error message will show with alarm sound or alarm 

vibration can for warning.

The battery is low.

Measurement was 

taken for samples with 

Brix lower than the 

measurement range.

Measurement 

was taken when 

the unit’s 

temperature was 

4˚C or lower.

Measured when 

the main unit’s 

temperature is 

exceeding 45

.

Measurement was 

taken when the 

sample’s temperature 

was 4˚C 

or lower.

Measured when 

t h e   s a m p l e ’ s  

temperature is 

exceeding 45

.

Measurement was 

taken for samples with 

Brix highter than the 

measurement range.

The instrument is 

faulty. 

Replace the batteries. Contact 

ATAGO if this error persists.

Main unit’s temperature 

error will preferentially 

display when the main unit’s 

and samples’ temperatures 

are both out of range.

When it is outside of temperature 

compensation range.

1. Insert a coin in the groove on the battery

 

 compartment cover. Turn the coin 

 

 counterclockwise to remove the cover.

2. Insert two batteries

3. Align the cover and push it down.

4. Close the battery compartment cover by 

  

pushing the cover in with a coin in the groove 

  

and turning it clockwise until it stops.

Observe the correct polarity.

Groove

When the 

cover is 

open

When the 

cover is 

closed

About battery indicator

When the battery icon indicates the low power 

level , replace both batteries with a brand new 

set of AAA alkaline batteries (1.5V).

*

Check the expiration dates on batteries before 

purchase.

Touch the sample and do not move.

Beep

Beep

Example

Note

Measurement was 

taken while the sample 

stage was not in  

contact with sample.

When correct measurements are 

not achievable due to interference 

from external light.

There is a temperature 

difference between the 

sample and the main 

unit.

Parts

Contents

Main unit (with silicone cover)

・・・・・・・・・・・・・・・・・・・・

1

Instruction Manual

 

(this book)

・・・・・・・・・・・・・・・・・・・・

1

Inspection Report

・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

1

・C

ushion RS 

Triple 

(for replacement)

・・・・・・・・・・・・・

2

AAA alkaline batteries

・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

2

AAA alkaline batteries are included. 

Light emitting part

Radiation 

temperature

sensor

Cushion RS

Triple

Receiver
START button

Battery compartment

Side button

Sample stage

LCD

Menu button

Lanyard hole

Measurement

8551-E02

Cat.No.8551

Digital Hand-held “Pocket” IR Brix Meter

PAL- HIKARi 51

Instruction Manual

The warranty period extension method 1 year  2 years

The warranty period will be extended from 1 year to 2 years when you register customer information. 
ATAGO Logger NFC can also be downloaded at the same time.

Trouble scanning the code? Access this link 

https://www.atago.net/ur/index.php?l=en

Full

When the history of measured data reaches 

100. 

Turn OFF the NFC Function or Delete 

Data History. 

17.7

18.2

18.4

18.1

17.7+18.2+18.4

3

→ 

18.3

Отзывы: