manualshive.com logo in svg

Asyst Technologies Advantag 9100, Техническое руководство

Поделиться
Скачать
Asyst Technologies Advantag 9100 Скачать руководство пользователя страница 32

Rev. AX5

Draft

Page 17

AdvanTag 9100 Technical Manual

Chapter 2: Theory of Operation

Data Storage—AdvanTag Reader

a

•  Read STATE Request - This message will query the CIDRW state of the transition 

model.

ASCII communication:

•  Are You There - This message is used to perform the heartbeat between the host 

and the connected device.

•  Read Attribute Request - This message requests the current values of ECID or 

SVID of the subsystem component indicated in TargetID.

•  Read Data Request - This message reads the “NOTEPAD” (Linear Memory) sec-

tion of the subsystem component indicated in TargetID.

•  Write Data Request - This message writes data to the NOTEPAD section of the 

subsystem component indicted in TargetID.

•  Read Material ID Request - This message is used to request the subsystem indi-

cated by TargetID to read an MID.

•  Write Material ID Request -This message is used to request the subsystem indi-

cated by TargerID to write Material identifier

•  Subsystem Command Request - This message is used to request the subsystem 

indicated in TargetID to perform a specific action. Included in this set are the fol-
lowing commands: SSCMD 04 - Blink LED on Node/Device; SSCMD 07 - Perform 
Diagnostics; SSCMD 13 - Reset; SSCMD 15 - Change State; SSCMD GetStatus.

•  Event Report Send - This message is used to send events to the host. Included in 

this set are the following commands: CEID 01 - Material (Pod/Cassette) Arrival 
Event; CEID 02 Material (pod/Cassette) Removal Event; CEID 03 - Operator 
Arrival Event; CEID 04 - Operator Leaving Event; CEID 08 - AdvanTag/LinkMan-
ager Power up.

•  Read STATE Request - This message will query the CIDRW state of the transition 

model.

Attribute Values:

T

ABLE

 3

Attribute Values (ECID and SVID)

Attribute

Description and Limits or Values

AlarmStatus

The Alarm Status
Value = 0 or 1

CarrierIDOffset

0 to CID_MAX_LENGTH-1
CarrierID CarrierIDLength <= 
CID_MAX_LENGTH

CarrierIDLength

1 to CID_MAX_LENGTH
CarrierID CarrierIDLength <= 
CID_MAX_LENGTH

CID_MAX_LENGTH

(8*N) N = Page1 to 17

Содержание Advantag 9100




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды