Asus RS700-E6 ERS4 страница 88 Скачать руководство пользователя

Страница: 88 / 138

6-4

Chapter 6: RAID configuration

3. The utility main window appears. Use the arrow keys to select an option from

the

Management Menu

and then press <Enter>. Refer to the Management

Menu descriptions on the next page.

At the bottom of the screen is the legend box. The keys on the legend box

allow you to navigate through the setup menu options or execute commands.

The keys on the legend box vary according to the menu level.

6.2

LSI Software RAID Configuration

Utility

The LSI MegaRAID software RAID configuration utility allows you to create RAID 0,

RAID 1, or RAID 10 set(s) from SATA hard disk drives connected to the SATA

connectors supported by the motherboard southbridge chip.

To enter the LSI MegaRAID software RAID configuration utility

1. Turn on the system after installing all the SATA hard disk drives.

2. During POST, the LSI MegaRAID software RAID configuration utility

automatically detects the installed SATA hard disk drives and displays any

existing RAID set(s). Press <Ctrl> + <M> to enter the utility.

• The LSI MegaRAID software RAID configuration utility automatically

configures to RAID 1 when the SATA to RAID Mode is enabled.

• The RAID setup screens shown in this section are for reference only and

may not exactly match the items on your screen due to the controller

version difference.

• When you create RAID sets with the LSI MegaRAID software RAID

configuration utility, the boot priority of the SATA optical drive has to be

manually adjusted. Otherwise, the system will not boot from the connected

SATA ODD.

LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008

BIOS Version A.08.09161344R

Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option

Management Menu

Configure

Initialize

Objects

Rebuild

Check Consistency

Configure VD(s)

LSI MegaRAID Software RAID BIOS Version A.08 09161344R

LSI SATA RAID Found at PCI Bus No: Dev No:1F

Device present at Port 0 ST3160812AS 152114MB

Device present at Port 1 ST3160812AS 152114MB

Device present at Port 2 ST3160812AS 152114MB

Device present at Port 3 ST3160812AS 152114MB

Press Ctrl-M or Enter to run LSI Software RAID Setup Utility.

Содержание RS700-E6 ERS4











































































































































Результаты поиска

Содержание RS700-E6 ERS4

Отзывы:

Похожие инструкции для RS700-E6 ERS4

Бренды по названию

Популярные бренды

Asus RS700-E6 ERS4, Руководство пользователя

Результаты поиска

Содержание RS700-E6 ERS4

Отзывы:

Похожие инструкции для RS700-E6 ERS4

Бренды по названию

Популярные бренды