CT-479 Installation guide/
3
4
Locate the 478-pin socket. Press the lever sideways then
lift it up to a 90º-100º angle to unlock the socket.
º
º
Position the CT-479 above the socket such that the
socket corner with small triangle matches the base of the
socket lever (A), then carefully insert the CT-479 into
the socket until it fits in place (B).
When the CT-479 is in place, push down the socket lever
to secure it. The lever clicks on the side tab to indicate
that it is locked.
Make sure that the CT-479 socket is unlocked (A).
Position a 479-pin CPU above the CT-479 socket such
that its marked corner matches the corner with small
triangle (B).
6
Carefully insert the CPU into the socket until it fits in
place (A) then use a flat-head screw driver to lock the
CPU in place (B).
N O T E :
N O T E :
N O T E :
N O T E :
N O T E : Make sure that the
socket lever is lifted up to a
90º - 100º angle; otherwise,
the CT-479 does not fit in
completely.
º
º
W A R N I N G :
W A R N I N G :
W A R N I N G :
W A R N I N G :
W A R N I N G : The CPU fits only
in one orientation. DO NOT
force the CPU into the CT-479
socket to prevent bending the
pins and damaging the CPU.
Q 2 0 4 7
Q 2 0 4 7
Q 2 0 4 7
Q 2 0 4 7
Q 2 0 4 7
1
2
W A R N I N G :
W A R N I N G :
W A R N I N G :
W A R N I N G :
W A R N I N G : The CT-479 fits
only in one orientation. DO
NOT force the CT-479 into
the socket to prevent
bending the pins.
Set the jumper according to your processor Front Side
Bus (FSB). Set the jumper labeled J 1
J 1
J 1
J 1
J 1 to pins 1-2 and 4-5
for FSB 400, or to pins 2-3 and 5-6 for FSB 533.
J1
®
POWER1
CT-479
mPGA479M
SOCKET
J1
FSB
400
3
6
2
5
1
4
3
6
2
5
1
4
FSB
533
12
Align the metal clip to the side rail of the CPU cooler (A)
and snap the hook of the metal clip into the hole (B).
Press down the locking lever and hook its end into the
other hole.
7
Connect the bundled 4-pin power cable to the CT-479
power connector labeled P O W E R 1
P O W E R 1
P O W E R 1
P O W E R 1
P O W E R 1.
13
Follow steps 11 and 12 to install the second clip, this
time in the reverse orientation of the first clip.
When the CPU cooler is in place, connect the CPU fan
cable to the CPU fan connector on the motherboard.
10
Fit the CPU cooler into the retention module. Orient the
CPU cooler such that the cleft is on the side with power
cable.
9
Remove the protective film and sticker that covers the
Thermal Interface Material (TIM) under the CPU cooler.
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT
• This module works only with qualified ASUS
motherboards and Intel
®
Pentium
®
M processors.
Refer to the module box for the list of qualified
motherboards and processors.
• If necessary, update the motherboard BIOS file.
• Visit the ASUS website (www.asus.com) for an
updated list of qualified motherboards and
processors, and to download the latest BIOS file.
• You cannot adjust the CPU voltage when using this
module.
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!
• Using this module with unqualified motherboards
and/or processors will damage the motherboard,
module, and/or processor.
®
®
15-061117001
www.asus.com
8
Connect the other end of the bundled 4-pin power cable
to a 4-pin ATX power connector from the power supply
unit.
A
A
A
A
A
B
B
B
B
B
A
A
A
A
A
B
B
B
B
B
I M P O R T A N T :
I M P O R T A N T :
I M P O R T A N T :
I M P O R T A N T :
I M P O R T A N T : Make sure
that the CPU cooler is
installed properly (i.e., not
inclined or tilted) to prevent
damage to the module and/
or processor.
5
A
A
A
A
A
B
B
B
B
B
11
A
A
A
A
A
B
B
B
B
B
