background image

 

 

GOVERNMENT REGULATIONS

 

This device complies with the requirements of Industry Canada (IC) - Management of Radiofrequencies, as 
specified in document CNR-210. Its use is authorized only on a no-interference, no-protection basis; in 
other words, this device must not be used if it is determined that it causes harmful interference to services 

authorized by IC. In addition, the user of this device must accept any radio interference that may be received, even if this 
interference could affect the operation of the device. 
 

 

 
 

This device complies with Part 15 of the FCC rules.  
Operation is subject to the following two conditions: 

(1)   this device may not cause harmful interference and 
(2)   this device must accept interference that may cause undesired operation. 

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the 
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to 
radio or television, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct 
the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult the dealer or an experienced radio / TV technician for help. 

 

Warning: 

Changes or modifications not expressly approved by <manufacturer> could void the user's authority to operate the 
equipment. 

 

 

 

  

E L E C T R O N I C S .  

6164 Chemin de Saint-Élie 

Sherbrooke, Qc, CANADA 

 J1R 0L1

 

 

 

E L E C T R O N I C   C O R P .

 

516A Elm Street 

M anchester, NH 03101 

USA

 

 

 

www.astroflex.com 

 

Содержание 2504A





















Отзывы: