background image

Printer Maintenance

QL-850 User Guide

44

 

6.

Use a clean, lint-free cloth dampened with isopropyl alcohol to clean the pinch rollers [3]. 
If necessary, you can rotate the rollers by turning the drive pulley [4].

Note: If isopropyl alcohol is insufficient, Goo Gone® may be used as an alternative.

7.

Position the roller cover plate [2] in the mounting location and install the two screws [1]. 
Installing the plate may require a small amount of force because of the tight fit.

8.

Close the top cover.

Cleaning the Maintenance Tray Area

During normal operation, waste ink is collected in the maintenance cartridge. Occasionally, 
drops of ink may be deposited outside of the cartridge into the maintenance tray area. You can 
temporarily remove the maintenance cartridge and clean the maintenance tray area as needed.

Note: For safety, keep the maintenance cartridge out of the reach of children. If ink is 
accidentally ingested, contact a physician immediately.

To prevent ink from leaking from a used maintenance cartridge, avoid dropping the 
cartridge or storing it at an angle. Otherwise, ink may leak and cause stains.

Ink adheres to the maintenance cartridge after it has been used. Handle the maintenance 
cartridge carefully. The ink may stain clothing.

Note: Wear protective gloves to prevent ink from staining your hands during this procedure.

1.

Power off the printer.

2.

On the rear of the printer, turn the power inlet switch off.

3.

Open the lower side door.

4.

Grasp the maintenance cartridge and carefully slide it out of the printer. Put the 
maintenance cartridge on a flat surface during the cleaning procedure.

5.

Dampen a clean, lint-free cloth with deionized water.

Do not use paper towels, napkins, or any other material that may leave lint or debris 
behind while cleaning. Problems can occur if lint enters the interior of the printer.

6.

Use the cloth to clean the empty maintenance tray area inside the printer.

7.

When you are finished cleaning the maintenance tray area, reinstall the maintenance 
cartridge.

8.

Close the lower side door.

[3]

[4]

Содержание QuickLabel QL-850
































































































































Отзывы: