background image

5

       WARNING 

Failure to position the parts in 

accordance with these diagrams 

or failure to use only parts 

specifically approved with this 

appliance may result in property 

damage or personal injury.

       AVERTISSEMENT 

Risque de dommages ou de 

blessures si les pièces ne sont 

pas installées conformément à 

ces schémas et ou si des pièces 

autres que celles spécifiquement 

approuvées avec cet appareil 

sont utilisées.

Installation and repair should be done by 

a qualified service person. The appliance 

should be inspected before use and at least 

annually by a professional service person. 

More frequent cleaning may be required due 

to excessive lint from carpeting, bedding 

material, etcetera. It is imperative that control 

compartments, burners and circulating air 

passageways of the appliance be kept clean.
L’installation et la réparation devrait être 

confiées à un technicien qualifié. L’appareil 

devrait faire l’objet d’une inspection par 

un technicien professionnel avant d’être 

utilisé et au moins une fois l’an par la suite. 

Des nettoyages plus fréquents peuvent être 

nécessaires si les tapis, la literie, et cetera 

produisent une quantité importante de pous-

sière. Il est essentiel que les compartiments 

abritant les commandes, les brûleurs et les 

conduits de circulation d’air de l’appareil 

soient tenus propres.

Do not use this appliance if any part has 

been under water. Immediately call a 

qualified service technician to inspect the 

appliance and to replace any part of the 

control system and any gas control which 

has been under water.
Ne pas utiliser cet appareil s’il a été plongé, 

même partiellement, dans l’eau. Ap-

peler un technicien qualifié pour inspecter 

l’appareil et remplacer toute partie du 

système de commande et toute commande 

qui a été plongée dans l’eau.

Only trim kit(s) supplied by the manufacturer 

shall be used in the installation of this ap-

pliance.
Seules les trousses de garniture fournies 

par le fabricant doivent être utilisées pour 

l’installation de cet appareil.

These appliances comply with National Safety 

Standards and are tested and listed by PFS  

(Report No. F14-172) to ANSI Z21.50 (in Canada, 

CSA-2.22), and CAN/CGA-2.17-M91 in both USA 

and Canada, as vented gas fireplaces.

These appliances may be used in bedrooms 

(USA only) when the room is an "unconfined 

space" as defined by the National Fuel Gas 

Code. Use in bedrooms may not be allowed 

by your local building codes. You should ob-

tain prior approval from the Authority having 

jurisdiction prior to installation.
Misc. Codes / Standards -

The Installation must conform to local codes or, 

in the absence of local codes, with the 

National 

Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest 

edition

 (In Canada, the current CAN/CGA-B149.1 

installation code).
The appliance, when installed, must be electri-

cally grounded and wired in accordance with 

local codes or, in the absence of local codes, 

with the 

National Electrical Code, ANSI/NFPA 

70 - latest edition

, or the 

Canadian Electrical 

Code, CSA C22.1 - latest edition

.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for 

service and proper operation. Never obstruct 

the front or  back openings of the appliance.

These appliances are designed to operate 

on natural gas only. The use of other fuels or 

combination of fuels will degrade the perfor-

mance of this system and may be dangerous.

These fireplaces are designed as decorative 

appliances and are not intended for use as area 

heaters. They must Not be equipped with wall 

thermostats or remote controls with thermostat 

functions.
These appliances must not be connected to a 

chimney or flue serving a separate solid fuel 

burning appliance.

The appliance area be kept clear and free from 

combustible materials, gasoline and other 

flammable vapors and liquids.
Millivolt Models - 

The millivolt appliances are 

manually controlled and feature a spark igniter 

(piezo) that allows the appliance's pilot gas to 

be lit without the use of matches or batteries.  

This system provides continued service in the 

event of a power outage. A manually-modulated 

gas valve is standard. Flame appearance and heat 

output can be controlled at the gas valve. The BTU 

Input for these appliances is shown in 

Table 1.

 Input (BTU) Gas Valves (all models)

All Models

Fuel Type

Input Rate (BTU / HR)

Millivolt

Natural

37,500 high - 30,000 low

Millivolt

Propane

34,000 high - 27,000 low

Table 1

       WARNING 

Improper installation, adjust-

ment, alteration, service or 

maintenance can cause injury 

or property damage.  Refer to 

this manual.  For assistance or 

additional information consult 

a qualified installer, service 

agency or the gas supplier.

       WARNING 

Failure to comply with these 

installation instructions will result 

in an improperly installed and 

operating appliance, voiding its 

warranty.  Any change to this appli-

ance and/or its operating controls 

is dangerous.

       WARNING 

Clothing or other flammable 

material should not be placed 

on or near the appliance.

       AVERTISSEMENT 

On ne devrait pas placer de 

vêtements ni d’autres matières 

inflammables sur l’appareil ni à 

proximité.

       WARNING 

THIS APPLIANCE MAY ONLY BE FITTED 

WITH DOORS CERTIFIED FOR USE 

WITH THE APPLIANCE.

       AVERTISSEMENT 

Tout écran ou protecteur retiré 

pour permettre l’entretien de 

l’appareil doit être remis en 

place avant de mettre l’appareil 

en marche.

       WARNING 

Any safety screen, guard, or 

barrier removed for servicing 

an appliance must be replaced 

prior to operating the appliance.

 

Содержание Marin40STTMN





















































Отзывы: