Assa Abloy Norton 6300 Series Скачать руководство пользователя страница 2

Copyright © 2017 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. 
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 

80-9363-0001-020 Rev 7 08/17

For assistance, contact Norton Technical Product Support 

at 800-438-1951 Ext 6030.

3000 Highway 74 East  •  Monroe, NC 28112

Tel: (800)-438-1951 ext. 6030

www.nor tondoorcontrols.com

suppor [email protected]

Index

Door Prep / Technical Data / Standard

Pull Side Back Plate Mounting / Install Back Plate Board

Pull Side Body Assembly Installation / Power Supply/Board Assembly Installation

Pull Side End Cap Installation / Pull Side Arm Installation

Closing Force Adjustment / Orienting Back Plate Ribbon Harness

Initial Setup

Set Application / Set Door Open and Closed Position

Opening and Closing Adjustments

Setting Accessory Dip Switches / Connecting Inputs

Cover Installation

Troubleshooting

Pull Side Template

Page 3

Page 4

Page 5

Page 7

Page 8

Page 9

Page 10

Page 11

Page 12

Page 13

Page 14

Page 15

IMPORTANT SAFETY INSTRUCTIONS - WARNING: 

To reduce the risk of severe injury or death

1) READ AND FOLLOW ALL INSTRUCTIONS.
2) Never let children operate or play with door 

controls. Keep the remote control (where provided) 
away from children.

3) Personnel should keep away from a moving door in 

motion.

4) Test the door’s safety features at least once a 

month. After adjusting either the force or the limit 
of travel, retest the door operator’s safety features.

    Failure to adjust the operator properly may 

cause severe injury or death.

5) KEEP DOOR PROPERLY OPERATING. See 

Door Manufacturer’s Owner’s Manual. An 
improperly operating door could cause severe 
injury or death. Have a trained door systems 
technician make repairs.

6)  SAVE THESE INSTRUCTIONS.

Page 2 

Содержание Norton 6300 Series
















Отзывы: