AsReader ASR-020D Скачать руководство пользователя страница 54

Страница: 54 / 162

C-5

Bookland ISBN Format

If Bookland EAN is enabled, select one of the following formats for Bookland data:

•

Bookland ISBN-10 - The decoder reports Bookland data starting with 978 in

traditional 10-digit format with the special Bookland check digit for

backward-compatibility. Data starting with 979 is not considered Bookland in this

mode.

•

Bookland ISBN-13 - The decoder reports Bookland data (starting with either 978 or

979) as EAN-13 in 13-digit format to meet the 2007 ISBN-13 protocol.

NOTE

For Bookland EAN to function properly, ensure Bookland EAN is enabled (see

Enable/Disable Bookland EAN on page C-4

), then select either Decode UPC/EAN

Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979

Supplemental Mode in

Decode UPC/EAN/JAN Supplementals on page C-6

Содержание ASR-020D



































































































































































Результаты поиска

Содержание ASR-020D

Отзывы:

AsReader ASR-020D, Руководство по параметрам, Страница: 54 / 162

Результаты поиска

Содержание ASR-020D

Отзывы: