AsReader ASR-020D Скачать руководство пользователя страница 11

Страница: 11 / 162

B-1

Set Default Parameter

You can reset the AsReader to two types of defaults: factory defaults or custom defaults.

Scan the appropriate bar code below to reset the decoder to its default settings and/or set its

current settings as custom defaults.



Restore Defaults - Scan this bar code to reset all default parameters as follows.

・

If you previously set custom defaults by scanning Write to Custom Defaults, scan

Restore Defaults to retrieve and restore the decoder’s custom default settings.

・

If you did not set custom defaults, scan Restore Defaults to restore the factory default

values listed in the table in page

A-1



Set Factory Defaults - Scan this bar code to restore the factory default values listed in

the table in page

A-1

This

deletes any custom defaults set.



Write to Custom Defaults - Scan this bar code to set the current decoder settings as

custom defaults.

Once set, you can recover custom default settings by scanning Restore Defaults.

Содержание ASR-020D



































































































































































Результаты поиска

Содержание ASR-020D

Отзывы:

AsReader ASR-020D, Руководство по параметрам, Страница: 11 / 162

Результаты поиска

Содержание ASR-020D

Отзывы: