background image

Estimated (calculated) altitudes:

 

with 

1/2A6-2: 100 feet/30.5 meters

 

with A6-4: 235 feet/71.5 meters

 

with A8-3: 265 feet/81 meters

 

with B4-4: 510 feet/155.5 meters

 

with B6-4: 510 feet/155.5 meters

 

with C6-5: 930 feet/283.5 meters

 

Aerospace  Speciality  Products  has  taken  reasonable 
care  in  the  design  and  manufacture  it’s  products. 
Aerospace  Speciality  Products  cannot  control  the  use 
and storage of same once sold and cannot assume any 
responsibility  for  personal  or  property  injury  resulting 
from  the use,  storage and/or  handling of  its  products. 
The  buyer  assumes  all  risks  and  liabilities  therefrom 
and  accepts  the  uses  Aerospace  Speciality  Products 
products  on  these  conditions.  No  warranty  either 
expressed  or  implied  is  made  regarding  Aerospace 
Speciality Products products, except for replacement or 
repair,  at  Aerospace  Speciality  Products

 

option,  of 

those products  proven to  be defective  in  manufacture 

within  one  month  from  date  of  original  purchase.  For 

repair  or  replacement  under  this  warranty,  please 

contact  Aerospace  Speciality  Products.  Proof  of 

Purchase will be required. Note: Your state may provide 

additional rights not covered by this warranty.

© 2015 Aerospace Speciality Products

Specifications:

!

Length: 15.5"/39.4 cm 

!

Diameter: 0.98"/24.9 mm

!

Weight: 1.1 oz/30 gm

!

Streamer Recovery

!

Recommended Engines: 

!

!

1/2A6-2; A6-4; A8-3; 

!

!

B4-4; B6-4; C6-5

!

Skill Level: Beginner

Kit EKTH - 18
This is a model rocket kit requiring 
construction. Tools, adhesives, 
finishing materials, launch equipment 
and engines are not supplied.

P.O. Box 1408, Gibsonton, FL 33534

www.asp-rocketry.com

Flying Model Rocket Kit

Содержание Theta 18










Отзывы: