Electric Screwdrivers
BTL-02B-ESD,
BTL-03B-ESD,
BTL-04B-ESD
Instruction Manual
Please Read Instructions
Before Operating
Adjusting the Torque (Cont.)
The tool should be run in reverse before to each test to make
sure the adapter is unwound and will allow the tool to achieve
rotation. Testing the tool without allowing any rotation will provide
incorrect readings. Start the test with the meter reading zeros. Pull
the trigger on the tool and let it run until it shuts off. The reading
on the meter will indicate the torque the driver achieved. Reverse
the tool, zero the meter and repeat the process several times to
see where the driver seems to be set. Tighten the Torque Adjusting
Nut to increase the torque, loosen the Torque Adjusting Nut to
decrease the torque. When the readings on the meter equal the
target torque run several tests to observe the scatter, or the “over/
under” You can “fine tune” the readings so that your target torque
will split the high and low readings. Visit the ASG Web page for
information on Torque Meters at www.asg-jergens.com
Locking the Torque Adjusting Nut
BTL tools are supplied with a torque cover to
protect the Torque Adjusting Nut. When the
torque has been adjusted to your satisfaction,
install the torque cover to prevent accidental
adjustment or tampering.
Adjusting the RPM
The speed of the BTL tools may be
adjusted without affecting the torque. The
RPM adjustment knob is located on the
BTL-1224 power supply next to the 5-pin
connector. Use a flat screwdriver bit to
adjust the knob. Turn clockwise to increase
RPM or counter clockwise to reduce RPM.
CAUTION: Do not force the knob past its
stopping point or you will damage it.
Standard Equipment
• 2, #64416, #0 bit*
• 1, #720718 1.5mm hex key
• 1, #915152, #1 bit
• 1, #728110 2m driver cord
*The spare #0 bit is provided to use for adjusting the RPM.
The drawing to the right shows
dimensions of the bits supplied.
Contact ASG for different styles,
lengths or diameters.
ASG, Division of Jergens, Inc.
15700
S. Waterloo Road | Cleveland, OH 44110-3898
Phone: (888) 486-6163 | Fax: (216) 481-4519
Email: [email protected] | Web: www.asg-jergens.com
Power Supply BTL-1224
BTL-2A24 Operating Instructions
Plug the Driver Cord in to the 5- Pin Connector on the Power Supply.
Plug the A/C Cord in to an A/C outlet. Turn the Power Switch to ON.
Turn the RPM adjustment knob with a flat screwdriver bit — turn it
clockwise to increase the RPM of the electric screwdriver and counter
clockwise to decrease the RPM.
Tool and Power Supply Specifications
Model
BTL-02B
BTL-03B
BTL-04B
Torque
Range
lbf.in
0.18-1.3
0.4-2.7
0.4-4.4
N.m
0.02-0.15
0.05-0.3
0.05-0.5
No Load RPM
Adjustment
100-750
100-750
100-750
Weight (g)
230
230
230
Length (mm)
190
190
190
Applicable Screw
Range
1.0-2.6
1.0-2.6
1.0-2.6
Applicable Bits
H4 (
Ø
4mm)
H4 (
Ø
4mm)
H4 (
Ø
4mm)
Input Voltage AC
#65688
110-240V - 50/60 Hz
Output Voltage DC
DC 24V (For Electric Screwdriver Use)
DC 12V (For Screw Counter Use)
Dimensions (mm)
70x125x60 (WxDxH)
Weight (g)
0.6 lb | 270g
Length of Cord (m)
5 ft | 1.5m
Revision: 07/28/202
