ASG ASG-CT2500 страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 53

background image

Page 13

Ensure the controller power cord can reach a properly grounded receptacle without creating a trip hazard in the work
area. The controller should also be mounted within view of the operator, and should be accessible and within reach for
programming and modification. Provide adequate clearance on all sides for access of technicians and

6” of clearance

below for cables to attach to the ports.

Tool Installation:

Connect the tool cable to the connector on the bottom of the controller by identifying the alignment tabs in the large
cable connector. Align these tabs and insert the cable to the controller, then rotate the twist-lock on the cable
connector clockwise until it

clicks

into place.

Note: To remove the cable from the controller, rotate the twist-lock on the cable connector counter-clockwise

until it pops free, and then remove the cable from the controller.

Obtain the ASG-SD2500 tool and identify the key slot on the screwdriver connector into which the screwdriver cable
connects. Find the red dot on the small end of the cable, and align it to the slot in the screwdriver connector. Insert the
cable to the tool firmly until it

clicks

into place.

Note: To remove the cable from the tool, slide the grip of the cable connector away from the tool, then pull the

cable out of the tool.

Connect the controller to the power source and power-up the controller.

Twist-lock

Alignment

Tabs

Grip

Dot

«
...
11
12
13
14
15
...
»

Содержание ASG-CT2500






















































Отзывы:

Нет отзывов

Похожие инструкции для ASG-CT2500

Бренд: Bartlett Страницы: 30

Бренд: Valve Concepts Страницы: 15

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: XBOX Страницы: 4

Бренд: Baby Trend Страницы: 8

Бренд: Baby Trend Страницы: 19

Бренд: Baby Trend Страницы: 5

Бренд: Baby Trend Страницы: 4

Бренд: K&K Страницы: 6

Бренд: Vageo Страницы: 2

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренд: Vacon Страницы: 30

Бренд: Vacon Страницы: 81

Бренд: Vacon Страницы: 100

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды