Asentria Teleboss 850 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 223

Asentria Teleboss 850 Скачать руководство пользователя страница 34

TeleBoss 850 2.06.280_STD User Manual

Page 28

IP Address Restrictions

TeleBoss 850 - IP Address Restrictions
No IP Restrictions Established
A) Add Item to Table

Enter your Selection: a
Enter IP addresses that are allowed access:
0.0.0.0 allows all IP addresses
255.255.255.255 restricts all IP addresses
XXX.XXX.XXX.0 allows all IP addresses in a subnet
XXX.XXX.XXX.255 restricts all IP addresses in subnet

New IP Restriction:

This menu is used to manipulate the IP Restrictions table. Refer to the

IP Address Restrictions

section in the

Features chapter for a detailed explanation of IP Address Restrictions. By default, no address restrictions are
configured.

Static Route Settings

TeleBoss 850 - Static Route Settings
A) Route 1
. . .
H) Route 8

Enter your Selection: a

TeleBoss 850 - Static Route 1 Settings
A) Enable [OFF]
B) Destination Network [0.0.0.0/0]
C) Gateway [0.0.0.0]
D) Interface [NONE]

Enter your Selection:

Static routes are network routes that specify in a more or less permanent way (

static

) that traffic to a certain

destination (destination host or destination network) gets

routed

out a certain interface or via a certain gateway.

Static routes gives you the ability to fine-tune how outbound network traffic leaves the unit for up to eight different
routes.

Enable

is an ON/OFF toggle to enable a static route. Default setting is OFF

Destination Network

is the network notation, i.e., w.x.y.z/s, where s is the significant bits. Default is 0.0.0.0/0.

Gateway

is the IP address of the gateway. Default setting is 0.0.0.0

Interface

displays a listing from which to select any one of the interfaces available on this T850

– None, Ethernet 1,

Ethernet 2, Ethernet 1 VLAN 1, 2, 3, 4, 5, 6, Ethernet 2 VLAN 1, 2, 3, 4, 5, 6, Dialup Modem PPP, and Wireless
Modem PPP. Default setting is NONE.

Refer to the

section in the Features chapter for a detailed explanation of Static Routes.

«
...
32
33
34
35
36
...
»

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды