manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 217

TeleBoss 850 2.06.280_STD User Manual 

 

Page 211 

 

 

T850 Hardware Revisions, Sensor Ports and Sensors  

 

Rev B    

No on-board sensor port: 

 

 

 

 

EventSensors (Type1) / CCU32/64 (Type1) 
Yes. Connect sensor to Serial Port I/O1 set to ESBUS mode, with an RS232/ES Bus Adapter (part #4162-010). 
 
PB1 
No 
 
EventSensor (Type2) / ES-CCU32/64 (Type2)  
Yes. 

IF

 the T850 has a 4SJ expansion card installed, connect to any 4SJ port with an ES-CAB8 cable. 

 
PB2 
No, a PB2 is only supported by on-board sensor ports, and will not work if connected to a 4SJ expansion card.  
Since the Rev B T850 has no on-board sensor port, the PB2 is not supported. 
 
SensorJack (Type3) 
No 
 
EventSensor (Type1) sensors cannot be daisy-chained with EventSensor (Type2) sensors; however, you can use 
EventSensor (Type1) sensors connected to Serial Port I/O1 

and

 EventSensor (Type2) sensors connected to a 

4SJ expansion card simultaneously.  Just make sure the DIP Switches on all are set so that there are no slotting 
conflicts. 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды