manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 156

TeleBoss 850 2.06.280_STD User Manual 

 

Page 150 

 

Syslog  

 
The Syslog IP Record Collection protocol allows the T850 to receive syslog messages from any Cisco voice-enabled 
router, including 

Cisco CallManager Express

. 

 

 
TeleBoss 850 - IP Record Collection (IPRC) Setup 
A) IP Record Collection                 [SYSLOG] 
B) Store Collected Data In              [FILE1] 
C) Data Alarm/Filter Enable             [OFF] 
D) Target Name                          [IPRC 1] 
E) TCP Port                             [1468] 
F) UDP Port                             [514] 
G) Time Stamping                        [OFF] 
H) Multiline Record Enable              [OFF] 
I) Division Target 1                    [] 
J) Division Target 2                    [] 
 

 

Syslog IP Record Collection protocol is based on the BSD Syslog protocol.  Messages are typically a single line of 
text, however, they are occasionally longer than one line of text (> 506 bytes) so the T850 features an option to break 
the oversize record into multiple lines, and assemble the component single lines into one multiline record.  The impact 
of this is that the user has to take this into account when defining data alarms.  To make it more predictable to the 
user where the unit divides an oversize message, there are additional settings called 

division targets

 (strings up to 8 

characters).  If the unit needs to divide an oversize message, it tries to make it so that the division target is the 
beginning of the remainder piece.  The BSD syslog protocol specifies that a message can be 1024 bytes.  So the 
worst case is that the unit must store a 1024-byte single-line record.  The minimum number of divisions necessary to 
break a 1024-byte message into records of acceptable size is 2.  Therefore there are 2 division target settings.  If the 
division targets fail to work through misconfiguration then the unit divides the message such that the 1st, 507th, and 
1013th bytes are the first bytes of each of the new records.  
 

IP Record Collection

 sets the protocol to be used to Syslog. 

 

Store Collected Data In

 toggles the FILE to which all incoming Syslog data will be stored.  Options are FILE1, FILE2, 

AUX1, AUX2, and AUX3.  Default setting is FILE1. 
 

Data Alarm/Filter Enable

 is an ON/OFF toggle to set whether configured Data Alarms or Filters will be applied to the 

incoming data.  Default setting is OFF. 
 

Target Name

 is the name used to identify the switch when an IPRC Connection Lost Alarm is sent via an 

AsentriaAlarm.  Default setting is IPRC 1. 
 

TCP Port

 sets the TCP port used by the sending Cisco device.  Default setting is port 1468. 

 

UDP Port

 sets the UDP port used by the sending Cisco device.  Default setting is port 514. 

 

Time Stamping

 is an ON/OFF toggle to set whether each individual call record is stamped with the Date and Time 

received in the T850.  Default setting is OFF. 
 

Multiline Record Enable

 displays the Multiline Record Settings menu. 

 

Division Target 1 / 2

 are eight charaters text strings used to designate the beginning of a section of a divided 

oversize record.  Default settings are blank. 
 
Multiline Record Settings 
 

 
TeleBoss 850 - IPRC Multiline Record Settings 
A) Multiline Record Enable              [OFF] 
B) Blank Line Count                     [0] 
C) Complex Multiline Detection          [OFF] 
 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды