manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 126

TeleBoss 830 2.11.370 STD User Manual     

 

Page 126 

 

Legacy Settings 

These settings are for support of older systems and should NOT be used for new implementations. We do not 

guarantee that these settings will be present in future versions or products.  These legacy settings are not on 

the Web Interface settings option. 

 

 
TeleBoss 830 - Legacy Settings 
A) Release Compressed                   [OFF] 
B) Autodelete After Polling             [OFF] 
C) Wait for NEXT                        [OFF] 
D) Omit END DATA                        [OFF] 
E) Line Tag                             [OFF] 
F) Release Mode                         [LINE] 
G) CBB DLE Stuffing                     [OFF] 
H) CBB Retransmits                      [5] 
I) CBB Timeout                          [15] 
   Note: These settings are for support of older systems and 
         should NOT be used for new implementations. We do 
         not guarantee that these settings will be present in 
         future versions or products. 
 

 

Released Compressed

  

This is an ON/OFF toggle to enable release of data in a compressed or uncompressed format.  The default 

setting is OFF. 

 

Autodelete After Polling

  

This setting is an ON/OFF toggle to enable the deletion of data from the call record database once it has been 

polled.  The default setting is OFF. 

 

Wait for NEXT  

Wait for NEXT

 

is an ON/OFF toggle that causes the unit to wait for the NEXT command before sending data 

once the RL command has been issued.  The default setting is OFF. 

 

Omit END DATA  

This is an ON/OFF toggle that

 

causes the unit to send or omit the string "END DATA" when a command 

processor poll is complete.  The default setting is OFF. 

 

Line Tag  

Line Tag

 

is an ON/OFF toggle that adds or omits the serial number line tags on each line of stored data.  The 

default setting is OFF. 

 

Release Mode

  

Release Mode toggles the following modes of releasing stored data:  LINE, XMODEM, and CBB.  Unless your 

application specifically uses XMODEM or CBB, leave this set to the default setting of LINE. 

 

CBB DLE Stuffing / Retransmits / Timeout  

These settings

 

are specific configuration options for polling via Compressed Binary Block (CBB) mode.  CBB 

is a release method included for compatibility and is not otherwise documented in this manual.

 

 

 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды