Radio transmitter kit of TV and CCTV signal - DIRECTIONAL.
Working with 4 cameras, range up to 1000 m
4 x transmitter T58M
antenna AP58S
receiver 4R58C
Installation :
Unpack the set. Open the lid with cableways . Prepare concentric cable to
video transmission (RG-59). Use heat-shrinkable film (as on the picture
below). Also prepare mains cable (LIYY 2 without audio signal or LIYY5x0.75
with audio signal
.
Channel selection:
Change the setting of the channel switch only
when the power is off.
Use the DIP switches to select the channel as
shown in the table.
The settings must be the same in both the
transmitter and the transmission path of receiver
All transmission path must be configured for different
channels (pre-set channels 1, 3, 5, 7).
(reading the channel number is only at powering)
Transmitters: thread the cables trough the proper cable bushing and connect to the clamp bar
according to the description below :
The package includes:
1. T58S transmitter (integrated with directional antenna) .............. 4 pcs
2. 4R58C - receiver (4 transmitters in continuous operation) ............ 1 pcs
3. AC adapter for the receiver ...................................................... 1 pcs
4
receiving antenna AP58S (directional, flat panel) ........................ 1 pcs
5. mounting bracket .................................................................... 5 pcs
6. instruction
Technical specifications:
amount of transmission paths ..................................................................... 4
range of frequency .................................................................................... 5740 - 5860MHz
amount of channel (frequency set independently for each transmission path) ... 7
supply: transmiterrs .................................................................................. 12V / 0,2A
supply: reciver (adapter included) ............................................................... 6V / 1A
transmitters: RF output power ........................ < 25mW (
video signal: parameters of input / output ..... 1V ; 75om
type video signal .......................................... PAL / NTSC
audio signal: parameters of input / output ....... 0.7V ; 1kom
modulation ................................................. FM
beamwidth (horizontal and wertical).................20 deg
polarization of antennas ................................. horizon
operating temp. range...................................... -40 +70 C deg
class of hermetic (only transmitters) ................. IP65
dimension of pack .......................................... 250x 170 x 360 mm
weight with packaging...................................... 4 kg
RF power compatible with CE)
1. video ground (RG-59 metallic shield)
2. video signal (RG-59 centre core)
3. audio L
4. audio R
5. - supply ground
6. + supply 12V
LED. supply lamp signal
A. adjustment of the camera output
Screw tight the screws on the cable bushings.
Using connection clips attach the devices to masts or extensions.
Connect the receiver to the panel antenna by coaxial cable (recommended type: TRI-LAN400).
Required to connect the connectors: N (antenna) and SMARP (receiver).
Antennas should be placed at highest possible place and
.
Since the devises work as directional antennas it is important that they are facing each other.
The holder can be ad/- a degree which helps to install the devises properly.
After finishing the installations the cables must be attached with the hose damps to the
mast on extension closely to the devises.
For transmitters use brand-good power supplies (output DC 12V, current 0,5A or more).
After turning on the power supply the signal transmissions starts on the channel chosen.
Transmitter is equipped with potentiometer, which allows to adjust the vision output to the camera
parameters. If these are such necessity (insufficient contrast) you can regulate the parameters
.
greater than 2,5m above the ground
office address:
ASE
Anielów 22
08-460 Sobolew
POLAND
- function relays
- automotive electronic circuits
- telecommunication systems
- custom orders
e-mail: ase@ase.hoste.pl
tel.: +48 720 239 596
Design and
production:
GB
PL
manual / instrukcja
www.ase.hoste.pl
office address:
ASE
POLAND
Anielów 22
08-460 Sobolew
- function relays
- automotive electronic circuits
- telecommunication systems
- custom orders
e-mail: ase@ase.hoste.pl
tel.: +48 720 239 596
Design and
production:
GB
PL
manual / instrukcja
www.ase.hoste.pl