manualshive.com logo in svg

ASD FieldSpec 3, Руководство пользователя

Поделиться
Скачать
ASD FieldSpec 3 Скачать руководство пользователя страница 63

ASD Document 600540 Rev. J

53   

FieldSpec® 3 User Manual

 www.asdi.com

Chapter 6  Transporting and Carrying the FieldSpec® 3

6.4

Protecting the Instrument in the Field

The Ergonomic Pro-Pack has a small interior pocket near its top which holds a 
rain flap, as is shown in 

Figure 6-19

 and 

Figure 6-20

.

The rain flap is water resistant, but not water proof.

In the event of bad weather out in the field, place the instrument controller 
into its compartment on the outside of the Ergonomic Pro-Pack. Make sure 
both the spectroradiometer and instrument controller are turned off. Then pull 
the rain flap out of its compartment and over the outside of the pack. The 
shoulder straps are still free allowing you to hike towards shelter.

Figure 6-18

Allow for proper ventilation of the FieldSpec 
spectroradiometer.

Figure 6-19

Rain flap storage in the Ergonomic Pro-Pack.

Содержание FieldSpec 3















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды