manualshive.com logo in svg

Ascotel 2025, Системное руководство, Страница: 219 / 265

Поделиться
Скачать
Ascotel 2025 Скачать руководство пользователя страница 219

Ascotel® IntelliGate® 2025/2045/2065 as of I7.9

Operation and Maintenance

219

sy

d-

020

4/1.

7 

– I7.

9

 – 1

2

.2009

Note:

It is not possible to downgrade by replacing the Flash card with the 
loaded system software as the EIM card is also changed to generation 
6.6 during the upgrade to I6.6.
Note: An I6.6 EIM card together with I6.5 system software triggers a 
first start.

6. 4. 11

System Downgrade from I7.x (x<5) to I6.6

A successful downgrade requires the existence of a corresponding system software 
and valid configuration data. AIMS is backward compatible, which means that it is 
not absolutely necessary to change AIMS (does not apply to AIMS versions 7.6 and 
later).

System Downgrade with Flash Card

The simplest way of obtaining an I6.6 from an I7.x (x<5) single system is to replace 
the Flash card with the loaded system software (see 

"Flash card", page 202

). The 

configuration data is also stored on the Flash card. After the start-up the system is 
ready to operate again with the old system configuration.

System Downgrade with Software Upload

If a Flash card with old system software is not available, follow the steps described 
below:

1.

Carry out an emergency upload as indicated in 

"Emergency Upload of the sys-

tem software", page 190

.

2.

Once the system has started up, load the saved configuration data using AIMS 
under 

"Restore"

, and save the data in the PBX with 

"Upload"

. The PBX reboots and 

is then ready for operation with the old system software and the familiar system 
configuration.

6. 4. 12

System Downgrade from I7.5 to I7.x (x<5)

A successful downgrade requires the existence of a corresponding system software 
and valid configuration data. AIMS is backwards compatible, which means that 
AIMS does not necessarily have to be changed.

Содержание 2025










































































































































































































































































Отзывы:

Нет отзывов