AS ONE NDK-1A-F Скачать руководство пользователя страница 1

For your safety & life span of the product, please read this "instruction manual" fully 

before using and keep these instructions.

After reading this instruction, keep it in a place where you can see it at any time. 

 

Make sure that this instruction with the product should be given to the following 

users for safe use.

Thank you for your selecting Digital Hotplate NDK Series.

Table of Contents

● Safety considerations...........................

1

● Caution during use...............................

2

● Installation instructions.......................

3

● Product overview.................................

4

● Order of the operation..........................

7

● SETUP group........................................

9

●  SETUP group function

 

(Alarm, temperature correction, etc.)

.................

11

● Setting the timer...................................

13

● Setting the program.............................

15

●  Other functions

 

(Key lock, indication of operation time, etc.)

........

17

● Error display.........................................

18

● When operating safety devices...........

18

● Factory defaults....................................

19

● About the maintenance.......................

19

● Trouble shooting..................................

20

● Specifications.......................................

21

● FAQs......................................................

22

● Contact information.............................

26

取扱説明書

Digital Hotplate

Instruction Manual

CORPORATION

NDK-1A-I, NDK-1A-F
NDK-2A-I, NDK-2A-F

1-4601-31-90,-91、1-4601-32-90,-91

Содержание NDK-1A-F




























Отзывы: