AS MOTOR AS-751 RC Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

background image

Page 21 / 49

9

AS-751 RC SAFETY SYSTEM

The AS-751 RC flail mower is remotely controlled. This means that the operator will at times
be away from the machine. In order to increase the safety for the operator and other persons, the
machine is provided with a safety system, which can be activated both manually and
automatically.

If the emergency stop is activated automatically, or if the emergency stop of the remote control
is activated, the following happens:

-

The motor stops.

-

The forward drive is put neutral.

-

The coupling of the mower remains engaged, until the motor stands
still.

When the emergency stop of the machine is activated, the power to all electric components will
be cut and cause the machine to stop.

If the mower gets out of reach of the radio signal Emergency stop is activated automatically
If the radio signal is disturbed

Emergency stop is activated automatically

Another machine is using the same radio
frequency

Emergency stop is automatically engaged

If dangerous situations occur

Activate the emergency stop at the machine

Activate the emergency stop of the remote
control

Flail mower is lifted into service position

Safety precautions will prevent the

Radio link between receiver and sender is not
established

motor from starting

Defective fuses

Emergency stop activated on remote control or
machine

«
...
19
20
21
22
23
...
»

Содержание AS-751 RC


















































Отзывы:

Нет отзывов

Похожие инструкции для AS-751 RC

Бренд: Walker Страницы: 100

Бренд: Webb Страницы: 28

Бренд: Parker Страницы: 26

Бренд: Cub Cadet Страницы: 68

Бренд: Jacobsen Страницы: 98

Бренд: Gtech Страницы: 32

Бренд: Yard-Man Страницы: 6

CRAFTSMAN 944.602212

Бренд: Sears Страницы: 52

Parklander 2690997

Бренд: Murray Страницы: 36

Бренд: Simplicity Страницы: 80

Бренд: Feider Machines Страницы: 27

Бренд: Ryobi Страницы: 13

Бренд: Ryobi Страницы: 48

Бренд: Ryobi Страницы: 24

Бренд: Ryobi Страницы: 25

Бренд: Ryobi Страницы: 348

Бренд: IronCraft Страницы: 44

Бренд: Columbia Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды