Arturia MiniFreak Скачать руководство пользователя страница 104

Страница: 104 / 112

15.2.3. Utility > Audio

•

Audio In Gain

: sets the input gain of the rear-panel Audio In jack, from -9 dB to

+24 dB.

•

Master Tune

: adjusts the MiniFreak's tuning by up to ±50 cents.

•

Stereo to Mono

: changes the Left and right + headphones outputs to be Mono.

•

Calib Cutoff

: calibrates the cutoff frequencies of the Analog Filter for each of the

MiniFreak's voices.

•

Calib Analog

: calibrates the analog audio path components for each of the

MiniFreak's voices.

The calibration process will show a progress bar as it proceeds; while it's running, the

MiniFreak can't be played, sequenced, or edited. When it's done, you'll be shown a

"calibration successful" message, and clicking the Preset/Edit/Filters encoder will exit the

menu.

The process can't be stopped once started, but it takes less than a minute (cutoff) to two

minutes (Analog) to complete.

15.2.4. Utility > Controls

•

Velocity and Aftertouch Curves

: set velocity and aftertouch response to linear,

logarithmic, or exponential curves. Discussed further in the

Keyboard Functions

[p.74]

chapter.

•

Knob Catch

: determines how a parameter will react if its stored value doesn't

match the physical setting of an analog knob, and the knob is turned. Options

include:

◦

Jump

: As soon as the physical knob is turned, the stored parameter

value instantly jumps to where the physical knob is set.

◦

Hook

: The parameter value doesn't change until the physical knob is

turned past the stored value.

◦

Scale

: When the physical knob is turned, the parameter goes from

the stored value to the physical knob position in such a way that the

parameter smoothly "catches up" to the knob.

•

Sustain Polarity

: used to set the Sustain Jack to respond to a pedal with a

normally-open or normally-closed switch.

•

AT Start Sens and AT End Sens

: sets the sensitivity of how quickly the aftertouch

sensor under the keyboard begins to send aftertouch data, and how quickly the

keyboard pressure reaches maximum aftertouch value.

•

Touch Button Sens

: Provides three level of sensitivity for the touch buttons (to the

exception of the touch wheels) allowing you to adjust the touch response to your

liking.

15.2.5. Utility > Global Scale

•

Global Scale and Global Root

: set the

Scale and Root [p.77]

for any Preset that

doesn't have its own stored Scale and Root.

Arturia - User Manual MiniFreak - The Utility Menu

Содержание MiniFreak

















































































































Результаты поиска

Содержание MiniFreak

Отзывы:

Похожие инструкции для MiniFreak

Бренды по названию

Популярные бренды

Arturia MiniFreak, Руководство пользователя

Результаты поиска

Содержание MiniFreak

Отзывы:

Похожие инструкции для MiniFreak

Бренды по названию

Популярные бренды