Arturia MICROFREAK Скачать руководство пользователя

Страница: 84 / 104

To clear the modulation in a track, press the Oct | Mod button several times until the light of

the track you want to erase blinks. Then hold Oct | Mod button and press the Hold icon.

Note:

A quick way to clear all modulation tracks is to hold the Oct | Mod button and press the

Hold icon repeatedly.

13.2.2. Real-time recording of modulation

Modulation recording in real time is similar to recording in step mode. The only difference is

that both Play and Record need to be active. Recording will occur from the first step where a

movement was recorded. It will then make one full loop and stop just before the step where

you started the modulation recording. Once the loop finishes, the Record button turns off

and real-time recording ends.

Erasing a modulation track is the same as in step-recording mode:

• Press and hold Oct | Mod
• Press “Hold” (no need to hold it)
• Current modulation track is erased
• Keep Oct | Mod held and press “Hold” to erase the next modulation track. Press

Hold repeatedly if you want to clear all modulation tracks.

Note:

It is possible to record knob movements from external controllers in the Sequencers

and to Record knob movements of the MicroFreak on external devices such a DAW.

For an overview of knobs/parameters that can be recorded in a modulation track refer to

the table in the step-time recording paragraph above.

13.2.3. Smoothing

Smoothing (also called "slew") makes modulation transitions less abrupt. It is the same

effect that you achieve by applying Glide to pitches: pitch changes will become more

gradual when you move from one pitch to another.

Smoothing does the same for modulation. You can apply it to each of the four modulation

tracks in Utility: select Utility>Preset>Seq (X) smooth. By substituting X with one, two, three or

four you apply the smoothing effect to one of the modulation tracks.

Smoothing works in both Step mode and Real-time mode but the setting with which a blank

sequence starts will be different:

• A new Seq Mod track that is created using step-recording is set to Smooth Off by

default.

• A new Seq Mod track that is created using the real-time recording is set to

Smooth On by default.

Note:

Overwriting on an existing track does not change the Smooth setting.

13.3. Fun with Sequences

To make a sequence come alive, it's good practice to add rests and ties to it. You have

64 sequencer steps at your disposal, so there is plenty of space to insert them. A 32-step

sequence with rests and ties played at double speed will sound a lot more interesting than

a 16-step sequence with all steps filled and played at normal speed.

Arturia - User Manual MicroFreak - The Sequencer

Содержание MICROFREAK









































































































Результаты поиска

Содержание MICROFREAK

Отзывы:

Похожие инструкции для MICROFREAK

Бренды по названию

Популярные бренды

Arturia MICROFREAK, Руководство пользователя

Результаты поиска

Содержание MICROFREAK

Отзывы:

Похожие инструкции для MICROFREAK

Бренды по названию

Популярные бренды