Arturia MICROFREAK Скачать руководство пользователя

Страница: 74 / 104

12.3. Arpeggio Rate

The Rate knob determines the speed of your arpeggios. When the Sync LED is "Off", Rate

changes are displayed as BPM (Beats Per Minute). The default rate is 120.0 bpm. In this

mode the Arpeggiator will operate independently from the internal clock or an external clock

source.

When Sync is "ON", the Arpeggiator will sync to the internal clock, and the Rate values are

shown as divisions from this clock. While moving the Rate knob keep an eye on the OLED

display: it will display the tempo value in tempo divisions. The Division Rate tells you how the

arpeggiator is currently synced to the clock. For example, if it reads 1/2 (one over two), it will

play a note with a length of two beats. If the display reads 1/4 the Arpeggiator plays quarter

notes (four notes per measure). It's useful to remember this, because this way of syncing is

the same for an arpeggio and the sequences. The available time divisions are listed below:

• 1 whole note

• 1/2 note

• 1/2 note triplet

• 1/4 note

• 1/4 note triplet

• 1/8 note

• 1/8 note triplet

• 1/16 note

• 1/16 note triplet

• 1/32 note

• 1/32 note triplet

Note:

1/4 corresponds to a standard metronome tick.

The Arpeggiator and the Rate knob

Arturia - User Manual MicroFreak - The Arpeggiator

Содержание MICROFREAK









































































































Результаты поиска

Содержание MICROFREAK

Отзывы:

Похожие инструкции для MICROFREAK

Бренды по названию

Популярные бренды

Arturia MICROFREAK, Руководство пользователя

Результаты поиска

Содержание MICROFREAK

Отзывы:

Похожие инструкции для MICROFREAK

Бренды по названию

Популярные бренды