ARTEX ELT 1000 Скачать руководство пользователя страница 31

Страница: 31 / 62

ARTEX PRODUCTS / ACR ELECTRONICS, INC.

DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE MANUAL

ELT 1000 (P/N: A3-06-2749-1)

Y1-03-0259 Rev. U

Company Confidential

Page 31 of 62

2-Wire Remote Switch (3 position switch):
1.

Push switch lever to “SELF-TEST” position for approximately 1 second, until LED blinks one time, then

release. Error codes will begin to display after about 1 second.

Regardless of how long the ELT has been in the active state, no self-test is performed at turn off using

the 2-wire switch.

BEEPS &

FLASHES

TEST RESULTS

INDICATION

System OK

One pulse two seconds long of the local LED, remote light,

and buzzer. This pulse is suppressed if problems are found
during self-test.

Code not used in the ELT 1000

Low output power

Bad load or faulty ELT

Terminate antenna cable at antenna connection end
w/50Ω load. Repeat self-test. If error clears, proceed

to step 3).

Terminate ELT output w/50Ω load. Repeat self-test.

If error persists, return to factory for servicing –
cannot field repair. If error clears, replace antenna
cable.

Check coax cable and connectors for shorts and
opens, bad center pin, etc. Disconnect, then

reconnect cable. Repeat self-test.

Check antenna ground for low resistance (should be

<100 m Ω)

Antenna should be 3’ away from any vertical metal.

Have antenna checked by factory.

No position data present (long message protocol only. Error is suppressed for short messages)

Aircraft navigation system “OFF”

Turn on navigation system

Faulty system interface wiring or
connections.

Check integrity of wiring and connections

G-Switch loop between pins 5 and 12 is not present

Jumper open

Verify D-Sub connector jumper is installed by checking for
less than 1Ω between pins 5 and 12. Repair as necessary.
NOTE: When the installed jumper is removed,

wait at

least 60+ seconds

before a test is done to get a

G-switch ‘open’ on the Self-Test (6 flash error)

Jumper missing

Install G-SW enable jumper between pins 5 and 12 in D-Sub

harness connector.

Battery Check

Battery operating time is > 1 hr

Replace battery pack

Battery voltage low

Replace battery pack

Battery memory read-write error

Repeat self-test. Replace battery pack if 7-flash persists.

Protocol programming data

Missing data such as ELT S/N or
aircraft tail number

ELT requires reprogramming w/appropriate data

Table 6 Self-test Error Codes

Содержание ELT 1000































































Результаты поиска

Содержание ELT 1000

Отзывы:

Похожие инструкции для ELT 1000

Бренды по названию

Популярные бренды

ARTEX ELT 1000, Описание, эксплуатация, установка и техническое обслуживание

Результаты поиска

Содержание ELT 1000

Отзывы:

Похожие инструкции для ELT 1000

Бренды по названию

Популярные бренды