Artesyn RTM-ATCA-9305 IO Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

Artesyn RTM-ATCA-9305 IO Скачать руководство пользователя страница 32

Hardware Preparation and Installation

RTM-ATCA-9305 IO Installation and Use (10010926-05

)

32

2.3

Power Requirements

The RTM has a maximum power dissipation of 30 W for a combined 12 V payload and 3.3 V
management supply.

2.4

Installing and Removing the RTM

2.4.1

Installing the RTM

You can install the RTM whether or not the front blade is installed.

2.4.1.1

Front Blade is Installed

Use this procedure to install the RTM when the front blade is installed.

This procedure assumes that your system is powered. If your system is unpowered, disregard
the blue LED and skip the respective step.

1. Locate the slot where the RTM is to be installed into the shelf's rear, which must be the

same as that of the front blade.

2. Open the lower handle of the front blade to power down its payload.

Damage of RTM and Front Blade
The RTM can be installed into a powered or non-powered system.
Installing the RTM with other blades may damage the RTM and the front blade.Only install
the RTM with the Artesyn ATCA-9305 blade.
Only install the RTM with the Artesyn ATCA-9305 blade.
Damage of Circuits
Electrostatic discharge and incorrect installation and removal of the product can damage
circuits or shorten their life.Before touching the product, make sure that you are working in
an ESD-safe environment or wear an ESD wrist strap or ESD shoes. Hold the product by its
edges and do not touch any components or circuits.

«
...
30
31
32
33
34
...
»

Содержание RTM-ATCA-9305 IO

































































Отзывы:

Нет отзывов