manualshive.com logo in svg

Artesyn MVME7616E Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Artesyn MVME7616E Series Скачать руководство пользователя страница 15

General Information

MVME7616E Transition Module Installation and Use (6806800A43F)

15

1.4

Serial Port Interface Modules

You may configure the asynchronous/synchronous serial ports (ports 3 and 4) to the 
appropriate interface by installing a Serial Interface Module (SIM). A SIM is a small “plug-in” 
printed circuit board that converts the TTL-level synchronous or asynchronous port signals to 
industry standard voltage levels used by the ports. The SIM contains the receiver and 
transmitter circuits for converting the input and output signals of the host VMEmodule to the 
appropriate serial data communication protocol.

The SIMs for the MVME761 are listed in the following table.

Additional SIMs may be released. Please see your Artesyn representative for a complete list of 
SIMS that are available for the MVME761-0x1.

1.5

P2 Adapter Boards

The P2 adapters route the asynchronous and synchronous port, printer port, and Ethernet 
signals to the MVME761 transition module.

Table 1-1 SIM Part Numbers 

Interface

Model Number

Part Number

EIA-232-D DCE

SIM232DCE5E

01-W3876B11A

EIA-232-D DTE

SIM232DTE5E

01-W3877B11A

Содержание MVME7616E Series

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды