Artesyn MITX-CORE-820 Скачать руководство пользователя страница 91

Страница: 91 / 133

BIOS

MITX-CORE-820 Installation and Use (6806800M10H

)

5.4.2.8.4 SB Azalia Configuration

5.4.2.9

Network Configuration

5.4.2.10 AMT Configuration

Table 5-22 SB Azalia Configuration Field Description

Field

Description

Azalia

Controls detection of the Azalia device.

Azalia internal HDMI codec

Enables/Disables internal HDMI codec.

Table 5-23 Network Configuration Field Description

Field

Description

PCH Internal LAN

Enables/Disables PCH Internal LAN

LAN OPROM Selection

This is used to select LAN OPROM for quick boot minimal
configuration.

Wake on PCH LAN

Enables PCH Internal wake on LAN capability.

Table 5-24 AMT Configuration Field Description

Field

Description

Intel AMT

Enables/Disables Intel(R) Active Management Technology BIOS
Extension. Note: iAMT H/W is always enabled. This option just
controls the BIOS extension execution. If enabled, this requires
additional firmware in the SPI device.

Intel AMT Hot Key

Enables or Disables Intel® AMT Hot-Key during POST to enter
MEBX setup.

Intel AMT Setup Prompt

Enables/Disables Intel® AMT Setup Prompt to wait for hot-key
to enter setup.

Содержание MITX-CORE-820






































































































































Результаты поиска

Содержание MITX-CORE-820

Отзывы:

Artesyn MITX-CORE-820, Инструкция по установке и эксплуатации, Страница: 91 / 133

Результаты поиска

Содержание MITX-CORE-820

Отзывы: