Artesyn MaxCore MC1600 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 118

Artesyn MaxCore MC1600 Скачать руководство пользователя страница 86

84

MC1600 Extreme Edge Server Installation and Use (6806870A02A)

System Installation

System Installation

4.4.2

Disconnect from the Power Feed

If you want to remove the server from the rack or cabinet, you must disconnect it from the
power feed. Make sure that the power feeds you plan to remove are powered off and cannot be
switched on while removing the server.

4.4.3

Removing the Server

To remove the server from a rack, proceed as follows:

1. Disconnect power input cables.

2. Disconnect all cables from the PCIe cards and from the I/O panel.

3. Remove the earth ground connection.

4. Loosen and remove the mounting screws.

5. Remove the system from the rack.

Short Circuit and Personal Injury
Make sure the power feeds are powered off and cannot be switched on while you are
working.
Make sure all power input lines are not energized. Use caution with the tools to prevent
a short circuit

«
...
84
85
86
87
88
...
»

Содержание MaxCore MC1600























































































































Отзывы:

Нет отзывов