Artesyn ATCA-F140 Скачать руководство пользователя страница 48

Страница: 48 / 138

Hardware Preparation and Installation

ATCA-F140 Installation and Use (6806800M67J

)

4. Firmly press the front of the QSFP+ transceiver to full push the transceiver in the module’s

transceiver socket. Make sure that it is fully engaged to prevent it from being accidentally
disconnected.

For optical QSFP+ modules, reinstall the dust plug into the portal. Do not remove it until the
network interface cable will be attached.

2.9.2

Removing QSFP+ Transceiver Modules

Procedure

1. For optical QSFP+ transceivers, disconnect the network interface cable from the QSFP+

transceiver connector.

2. Do the following steps to remove QSFP+ transceivers with a bail-clasp latch:



Turn the bail-clasp down to the horizontal position.



Install the dust plug into the transceivers optical bore.



Hold the sides of the QSFP+ transceiver and slide it out of the module socket.

3. Do the following steps to remove QSFP+ transceivers with a pull tab latch:



Install the dust plug into the transceiver’ optical bore.



Hold the tab and pull the receiver gently to release the transceiver from the socket.



Slide the transceiver from the socket.

Place the QSFP+ transceiver into an anti-static bag.

Содержание ATCA-F140











































































































































Результаты поиска

Содержание ATCA-F140

Отзывы:

Бренды по названию

Популярные бренды

Artesyn ATCA-F140, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ATCA-F140

Отзывы:

Бренды по названию

Популярные бренды