manualshive.com logo in svg

ARTERY AT32F435 Series, Справочное руководство

Поделиться
Скачать
ARTERY AT32F435 Series Скачать руководство пользователя страница 362

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 362 

 

Rev 2.03

 

Figure 18-6

 Repetition mode 

ADC_IN5

ADC_IN0

OCLEN=1, OSN1=ADC_IN5, OSN2=ADC_IN0

Ordinary channel 

trigger

OCCE flag set

PCLEN=1, PSN3=ADC_IN14, PSN4=ADC_IN1

ADC_IN14

ADC_IN1

PCCE flag set

ADC_IN5

ADC_IN0

OCCE flag set

ADC_IN14

   

Sampling

Conversion

 

18.4.3.4  Partition mode 

The partition mode of the ordinary group can be enabled by setting the OCPEN bit in the ADC_CTRL1 
register. In this mode, the ordinary group conversion sequence length (OCLEN bit in the ADC_OSQ1 
register) is divided into a smaller sub-group, in which the number of the channels is programmed with 
the OCPCNT bit in the ADC_CTRL1 register. A single trigger event will enable the conversion of all the 
channels in the sub-group. Each trigger event selects different sub-group in order. 
Set the PCPEN bit in the ADC_CTRL1 register will enable the partition mode of the preempted group. 
In this mode, the preempted group conversion sequence length (OCLEN bit in the ADC_OSQ1 register) 
is divided into a sub-group with only one channel. A single one trigger event will enable the conversion 
of all the channels in the sub-group. Each trigger event selects different sub-group in order.   
The partition mode cannot be used with the repetition mode at the same time. Figure 18-7 shows an 
example of the behavior in partition mode for ordinary group and preempted group. 
Figure 18-7

 Partition mode  

ADC_IN5

ADC_IN0

OCLEN=4, OCPCNT=1, OSN1=ADC_IN5, OSN2=ADC_IN0, OSN3=ADC_IN2, OSN4=ADC_IN1, OSN5=ADC_IN7

Ordinary channel 

trigger

CCE flag set

PCLEN=2, PSN2=ADC_IN14, PSN3=ADC_IN1, PSN4=ADC_IN13

ADC_IN2

ADC_IN1

ADC_IN7

Ordinary channel 

trigger

CCE flag set

ADC_IN5

Ordinary channel 

trigger

ADC_IN14

ADC_IN1

Preempted 

channel trigger

PCCE flag set

ADC_IN13

ADC_IN14

Preempted 

channel trigger

Preempted 

channel trigger

Preempted 

channel trigger

CCE flag set

Ordinary channel 

trigger

ADC_IN0

CCE flag set

Sampling

Conversion

 

18.4.4  End of conversion 

The ADABRT bit in the ADC_CTRL2 register can be used to stop ADC conversions. At the end of the 
conversions, the conversion sequence returns to the first channel. This allows the user to configure a 
new channel sequence, and the ADC starts conversions from the beginning based on the new order 
when a trigger event occurs. Figure 18-8 shows the timing diagram when the ADABRT bit is set. 

Содержание AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды