manualshive.com logo in svg

ARTERY AT32F435 Series, Справочное руководство

Поделиться
Скачать
ARTERY AT32F435 Series Скачать руководство пользователя страница 348

  AT32F435/437

 

Series  Reference  Manual

 

2022.11.11

 

Page 348 

 

Rev 2.03

 

1: Reference clock detection enabled 

Bit 3 

TSEDG 

0x0 

rw 

Timestamp trigger edge 
0: Rising edge 
1: Falling edge 

Bit 2: 0 

WATCLK 

0x0 

rw 

Wakeup timer clock selection 
000: ERTC_CLK/16 
001: ERTC_CLK/8 
010: ERTC_CLK/4 
011: ERTC_CLK/2 
10x: ck_b 
11x: ck_b is selected. 2

16 

is added to the wakeup counter 

value, and wakeup time =E2

16

. 

Note:  The  write  access  to  this  field  is  supported  when 
WATEN=0 and WATWF=1.

 

17.4.4  ERTC initialization and status register (ERTC_STS)  

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 17  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 16 

CALUPDF 

0x0 

ro 

Calibration value update complete flag 
0: Calibration value update is complete 
1: Calibration value update is in progress 
This  bit  is  automatically  set  when  software  writes  to  the 
ERTC_SCAL  register.  It  is  automatically  cleared  when  a 
new calibration value is taking into account. When this bit is 
set,  the  write  access  to  the  ERTC_SCAL  register  is  not 
allowed. 

Bit 15 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 14 

TP2F 

0x0 

rw0c 

Tamper detection 2 flag 
0: No tamper event 
1: Tamper event occurs 

Bit 13 

TP1F 

0x0 

rw0c 

Tamper detection 1 flag 
0: No tamper event 
1: Tamper event occurs 

Bit 12 

TSOF 

0x0 

rw0c 

Timestamp overflow flag 
0: No timestamp overflow 
1: Timestamp overflow occurs 
If a new time stamp event is detected when time stamp flag 
(TSF) is already set, this bit will be set by hardware. 

Bit 11 

TSF 

0x0 

rw0c 

Timestamp flag 
0: No timestamp event 
1: Timestamp event occurs 
It  is  recommended  to  double  check  the  TSOF  flag  after 
reading  a  timestamp  and  clearing  the  TSF.  Otherwise,  a 
new timestamp event may be detected while clearing the 
TSF.   

Note: The clearing operation of this bit takes effect after two 
APB_CLK cycles. 

Bit 10 

WATF 

0x0 

rw0c 

Wakeup timer flag 
0: No wakeup timer event 
1: Wakeup timer event occurs 

Note: The clearing operation of this bit takes effect after two 
APB_CLK cycles. 

Bit 9 

ALBF 

0x0 

rw0c 

Alarm clock B flag 
0: No alarm clock event 
1: Alarm clock event occurs 

Note: The clearing operation of this bit takes effect after two 
APB_CLK cycles. 

Bit 8 

ALAF 

0x0 

rw0c 

Alarm clock A flag 
0: No alarm clock event 
1: Alarm clock event occurs 

Note: The clearing operation of this bit takes effect after two 
APB_CLK cycles. 

Bit 7 

IMEN 

0x0 

rw 

Initialization mode enable 
0: Initialization mode disabled 

Содержание AT32F435 Series





































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды