manualshive.com logo in svg

ARTERY AT32F413 Series, Справочное руководство, Страница: 262 / 369

Поделиться
Скачать
ARTERY AT32F413 Series Скачать руководство пользователя страница 262

  AT32F413

 

Series  Reference  Manual

 

2022.06.27

 

Page 262 

 

Rev 2.00

 

17.5.2  RTC control register low (RTC_CTRLL) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 15: 6 

Reserved 

0x000 

resd 

Kept at its default value. 

Bit 5 

CFGF 

0x1 

ro 

RTC configuration finish 
Indicates  whether  the  last  write  operation  on  the  RTC 
registers has been completed or not. Write access to the 
RTC registers is allowed only when this bit is set. 
0: Last write operation on RTC registers is ongoing 
1: Last write operation on RTC registers ends. 

Bit 4 

CFGEN 

0x0 

rw 

RTC Configuration enable 
This bit is set to enter configuration mode in order to enable 
write access to the CNT, ALA, DIVCNT registers. 
0: Exit configuration mode 
1: Enter configuration mode 

Bit 3 

UPDF 

0x0 

rw0c 

RTC update finish flag 
This bit indicates wheter the update of the RTC registers 
has  been  completed  or  not.  This  bit  is  set  by  hardware 
when the CNT and DIVCNT are updated. Before any read 
operation,  this  bit  must  be  cleared  by  software,  and  the 
user must wait until this bit is set.

 

0: RTC registers not updated. 
1: RTC registers updated. 

Bit 2 

OVFF 

0x0 

rw0c 

Overflow flag 
This bit is set when the counter overflows. An interrupt is 
generarted if OVFIEN

 

=1. 

0: Overflow not detected. 
1: Overflow occurred. 

Bit 1 

TAF 

0x0 

rw0c 

Time alarm flag 
This bit is set when an alarm event is detected. An interrupt 
is generated if TAIEN

 

=1. 

0: Alarm not detected. 
1: Alarm detected. 

Bit 0 

TSF 

0x0 

rw0c 

Time second flag 
This bit is set when a second event is detected. An interrupt 
is generated if TSIEN

 

=1.   

0: Second event not detected. 
1: Second event detected. 

17.5.3  RTC divider register (RTC_ DIVH/RTC_DIVL) 

RTC divider register high (RTC_DIVH) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 15: 4 

Reserved 

0x000 

resd 

Kept at its default value. 

Bit 3: 0 

DIV 

0x0 

wo 

RTC divider 
This  field  is  used  to  define  the  counter  clock  frequency 
according to the formula: 
fLN_CLK = fRTCCLK/(DIV[19: 0]+1) 

RTC divider register high (RTC_DIVL) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 15: 0 

DIV 

0x8000 

wo 

RTC divider 
This  field  is  used  to  define  the  counter  clock  frequency 
according to the formula: 
fLN_CLK = fRTCCLK/(DIV[19: 0]+1) 
Note: the zero value is not recommended.

 

Содержание AT32F413 Series


















































































































































































































































































































































































Отзывы:

Нет отзывов