ARRI ARTEMIS 2 Скачать руководство пользователя страница 69

Страница: 69 / 93

Installation and Operation

8.5.3 Jog-Wheels

Once the Jog-Wheels have been assigned a function, these can

be used to quickly and intuitively change

values such as speed, ramp by turning the Jog-Wheel.

At the same time, the button function allows you to turn

ON / OFF

functions such as:

Home Position, True Tilt, True Pan, etc.

8.5.4 Radio Module

Attaching the Radio Module

1. Open both Rod Clamp Bridge screws to allow some more

clearance.

2. Insert the Radio Module by fitting it into the radio module slot

and sliding it downwards until the Radio Release Button pops

back out.

3. Tighten both screws again.

Removing the Radio Module

1. Open both Rod Clamp Bridge screws to allow some more

clearance.

2. Press the Radio Release Button.

Pull the radio module out of the radio module slot.

3. Pull the radio module out of the radio module slot.

4. Tighten both screws again.

Содержание ARTEMIS 2






























































































Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Бренды по названию

Популярные бренды

ARRI ARTEMIS 2, Руководство пользователя

Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Бренды по названию

Популярные бренды