ARO RS25A–VLK, Руководство оператора

Страница: 5 / 8

5
1 Housing 49812–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Valve Stem 48065–2 . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Lever 49936 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Roll Pin
Y178-134
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Grip Ring 49798 . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Seat 48071 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Tip Valve 48070 . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Spring 32858 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Inlet Adapter 49824 . . . . . . . . . . . . . . . . . . . . . . . .
10 Muffler Tube 48263–1 . . . . . . . . . . . . . . . . . . . . . . . . .
11 Dowel Pin Y148–16 . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 Shroud
for models RS25A–VLK
48876 . . . . . . . . . . . . . .
for models RS26A–VLK 48878 . . . . . . . . . . . . . .
15 Retaining Ring 44533 . . . . . . . . . . . . . . . . . . . . . . .
16 Bearing (2 req’d) 48169–1 . . . . . . . . . . . . . . . . . . . . .
17 Rear End Plate 48872 . . . . . . . . . . . . . . . . . . . . . .
18 Cylinder (includes roll pin) 49815 . . . . . . . . . . . . .
19 Seal 49819 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 Rotor 48253–1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 Blade (5 req’d) 48254–1 . . . . . . . . . . . . . . . . . . . . . . .
22 Front End Plate 48871 . . . . . . . . . . . . . . . . . . . . . .
23 O Ring Y325–223 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24 Lock Ring 48257–1 . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 Key 39442 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26 Counterbalance (includes needle bearing)
for models RS25A–VLK
49808–5 . . . . . . . . . . . . . .
for models RS26A–VLK 49808–6 . . . . . . . . . . . . . .
27 Spindle Assembly (includes bearing) 49807 . . . .
28 Retaining Ring Y147–125 . . . . . . . . . . . . . . . . . . . . . . .
30 Wrench (not shown) 30131–2 . . . . . . . . . . . . . . . . . .
31 Eductor Assembly 49976 . . . . . . . . . . . . . . . . . . . .
Service Kit: includes items 8, 15, 16, 21,
27 and 28
49837 . . . . . . . . . . . . . . . . . . . . . . . . . .
DISASSEMBLY/ASSEMBLY INSTRUCTIONS
Always wear eye protection when operating or performing
maintenance on this tool.
Always turn off the air supply and disconnect the air sup-
ply hose before installing, removing or adjusting any
accessory on this tool or before performing any mainte-
nance on this tool.
•
Never apply excessive pressure by a holding device which
may cause distortion of a part.
•
Apply pressure evenly to parts which have a press fit.
•
Apply even pressure to the bearing race that will be press
fitted to the mating part.
•
Use correct tools and fixtures when servicing this tool.
•
Don’t damage ‘‘O” rings when servicing this tool.
•
Use only genuine ARO replacement parts for this tool. When
ordering, specify part number, description, tool model number
and serial number.
MOTOR DISASSEMBLY
– Remove retaining ring (28).
– Remove spindle assembly (27) (includes bearing). NOTE: Do
not attempt to remove bearing from spindle.
– Remove lock ring (24) and pull motor and seal (19) from hous-
ing.
– Remove retaining ring (15).
– Using special brass blocks to fit around o.d. of cylinder, clamp
around cylinder and press shaft of counterbalance thru bear-
ing (16) and end plate (17).
– Remove blades (21), rotor (20) and key (25).
– Remove end plate (22) and bearing (16).
– Do not remove dowel pin (11) from housing (1) unless damage
is evident. To remove, press pin out from inside of housing.
MOTOR ASSEMBLY
– Assemble dowel pin (11) into housing (1), pressing flush with
surface of housing.
– Grease and assemble ‘‘O” ring (23) to lock ring (24).
– Assemble lock ring (24) over counterbalance (26).
– Assemble bearing (16) into end plate (22), pressing on outer
race of bearing.
– Assemble end plate (22) onto shaft of counterbalance, press-
ing on inner race of bearing.
– Install key (25) in key slot.
– Assemble rotor (20) to counterbalance, aligning keyway to
key (25).
– Assemble five rotor blades (21) to rotor slots.
– Assemble cylinder (18) over rotor, aligning roll pin in cylinder
with slot in end plate.
– Assemble bearing (16) into end plate (17), pressing on outer
race of bearing.
– Assemble end plate (17), with bearing (16), to counterbal-
ance, pressing on inner race of bearing. NOTE: Align slot in
end plate with roll pin in cylinder.
– Install retaining ring (15) to groove in counterbalance, with
bow in ring positioned as shown on parts illustration page.
– Assemble seal (19) to grooves in cylinder.
– Assemble motor to housing, aligning seal (19) with air inlet.
– Tighten lock ring (24), securing motor assembly.
– Lubricate needle bearing, contained in counterbalance, with
ARO 33153 grease.
– Assemble spindle assembly (27) to counterbalance, securing
with retaining ring (28).
PART NUMBER FOR ORDERING PART NUMBER FOR ORDERING