Armstrong ABH 299 Скачать руководство пользователя страница 47

Страница: 47 / 72

North America • Latin America • India • Europe / Middle East / Africa • China • Pacific Rim

armstrong

international.com

Designs, materials, weights and performance ratings are approximate and subject to change without notice. Visit

armstrong

international.com for up-to-date information.

Maintenance

Periodic Maintenance of Heater and Inspections

All high efficiency condensing appliances will require more regular maintenance (cleaning) than their non-condensing counterparts.

Failure to do so may result in damage to the appliance that is not covered under warranty. Failure to follow all of the instructions

contained in this manual may also cause premature product failure that may not be covered under warranty.

Periodic maintenance should be performed at least once a year by a qualified service technician to ensure that all the equipment is in

safe, efficient operation.

Failure to do so may eliminate warranty coverage.

In the first year of operation, it is highly recommended

that inspections of all connection points and the combustion chamber be done at three month intervals, any signs of fouling or

leaks must be thoroughly investigated immediately as failure to do so may void warranty. Assuming no cause for excessive fouling

is found, then the period of months from initial start up that it was found that cleaning was required, shall become the required

future minimum cleaning interval, but at no time should it exceed 12 months. The owner MUST make necessary arrangements with

a qualified heating contractor for proper maintenance of the heater. Installer must also inform the owner that the lack of proper care

and maintenance of the heater may result in a hazardous condition and lack of warranty coverage. The installer should discuss the

contents of the User’s Information Manual with the owner.

Annual Inspection

(See the Maintenance Checklist for required tools and materials)

An inspection should cover, at a minimum, the following areas:

• Inspect all fittings, controls and connections for leaks, damage, or fouling
• Fire side:

-Heat exchanger

-Burner and ignitor

-Burner door and rear wall insulation

• Drain system components:

-Hoses & clamps

-Trap assembly

-Condensate neutralizer

• Test all safeties and operating controls
• Water side temperature rise (∆T) test

Inspection And Cleaning (photos illustrating each step follow sets of instructions)

• Remove the front cover and check the sensors, transducers, all pipes, lines and

connections, and the heat exchanger (top, bottom) for traces of water and water leakage.

• Inspect the top of the casing and/or the top of the appliance for water leakage or traces of

water from the air supply pipe or the air vent (if applicable).

• Dismantle the burner unit: remove the (6) 6mm nuts (with a 10mm socket), the ignition

cable, the power and speed control plugs, and the ground wire from the fan, and remove

the burner/fan unit from the heat exchanger and cabinet.

• After the burner door is removed, it should be thoroughly inspected before being put back

into service. There are two gaskets on the burner door; the first is the inner rope gasket,

which is permanently affixed to the burner door. If this gasket is completely compressed

(having no sealing ability), the door must be replaced. The second gasket is on the

perimeter and is made of rubber; this gasket is easily replaced, and comes as a standard

part of a maintenance kit (and should always be replaced during the annual maintenance

procedure.

NOTE: Over-tightening the M6 nuts may cause the threaded rods on the front of the

heat exchanger to break! If excess resistance is encountered when installing a M6 nut,

discard that nut and use one of the spares shipped with the unit. The maximum torque

for assembling a burner door nut is 5.9 ft-lb or 70.8 in-lb. Use a torque wrench suitable

for this torque range to tighten the nuts.

Complete burner, door &

fan assembly removed for

inspection

CAUTION! Before removing the door of the appliance, switch off the electrical power supply to it.

Содержание ABH 299









































































Результаты поиска

Содержание ABH 299

Отзывы:

Похожие инструкции для ABH 299

Бренды по названию

Популярные бренды

Armstrong ABH 299, Руководство по установке и эксплуатации

Результаты поиска

Содержание ABH 299

Отзывы:

Похожие инструкции для ABH 299

Бренды по названию

Популярные бренды