Wireless Light Switch
With wall mountable transmitter
Model # AL-28068
Add switched outlet convenience without new wiring, works through
walls and doors up to 50 feet away. Wireless wall transmitter looks and
operates like a traditional designer-style wall light switch, easily surface
mounts to wall. Can also be converted to a small hand-held remote
wireless switch. Requires a 3 volt CR2032 lithium battery, included.
OPERATION
All transmitters and receivers come pre-programmed, or “paired,”
and are ready to use.
1. Plug the receiver into a 120V AC electrical outlet.
2. To test, plug an electrical device like a lamp into the receiver’s
outlet located at the bottom of the unit. Make sure that your
electrical device is powered ON.
3. On the transmitter switch, push the top portion of the rocker switch
to turn the device ON or bottom portion to turn the device OFF.
Manual Override: You can manually power the unit ON/OFF by
pressing the lighted ON/OFF override button located on the front
of the Receiver. (Do not hold the button down for manual ON/OFF
operation as this will cause the unit to enter the pairing mode.)
If you want to control multiple receivers with a single transmitter, the
units must be paired. Test the transmitter with the receivers. If the
receivers do not respond, they must be re-paired.
Pairing
1. Press and hold the ON/OFF button on the receiver for 3
seconds. The LED indicator will begin to flash slowly.
2. Press on then off on the transmitter.
To un-pair:
1. Press and hold the ON/OFF button on the receiver for 3
seconds. The LED indicator will begin to flash slowly.
2. While the LED indicator is slowly flashing press and hold the
ON/OFF button for another 3 seconds and the LED indicator
will begin to flash quickly.
3. Press the ON/OFF button on the receiver again and all
transmitters will be un-paired to that receiver.
Note: Each receiver can only have two transmitters paired to it at a
time. Each transmitter can control up to four receivers.
TROUBLESHOOTING
The wireless switch receiver does not turn on
■
■
Make sure the unit is securely plugged into an AC power outlet.
■
■
Unplug the unit for a moment, and then plug it back in again.
■
■
Check the outlet by plugging in another device.
The remote transmitter does not work
■
■
Make sure the battery is fresh.
■
■
Move the transmitter closer to the receiver. Actual operational
distance will vary based on walls, obstructions and other nearby
electronic devices.
■
■
Reset the receiver and pair transmitter with new code.
Battery
Compartment
Battery replacement
The remote transmitter uses a 3 volt CR2032 lithium battery.
To replace, slide unit out of wall mount and remove battery from
compartment. Insert new CR2032 lithium battery, making sure to
match up the + and – polarity markings. To test, press the ON or
OFF buttons and make sure the LED indicator on the unit lights up.
Do not dispose of batteries in fire. Batteries may explode or leak.
CAUTION: DO NOT plug more than a total of 600 watts into the
wireless receiver.
SPECIFICATIONS
■
■
Operating temperature range: 0°C (32°F) to 45°C (113°F).
■
■
Rated: 120VAC/60Hz/5A/600W Resistive, 5A/600W Tungsten,
500VA Electronic Ballast
■
■
Wireless working frequency: 315 MHz
This item is a Radio Frequency Device (RF), and as such the range of the remote
control is dependent on many factors. Actual operational distance will vary based
on walls and line of sight obstructions, and other nearby electronic devices.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications to
this unit not expressly approved by the party responsible for compliance could
void the user authority to operate the equipment.
Limited 3-year warranty. This product is for dry location use only. Improper
installation, improper powering, abuse, or failure to use this device for its
intended purpose will void warranty. Proof of purchase is required for all
returns. Questions? Email [email protected].
© 2012-16 Armacost Lighting. All rights reserved.
160707
