manualshive.com logo in svg

ARM V2M-Juno r2, Техническое справочное руководство, Страница: 37 / 150

Поделиться
Скачать
ARM V2M-Juno r2 Скачать руководство пользователя страница 37

nTRST

This resets the CoreSight DAP and the TAP controllers inside the Juno r2 SoC.

CFG_nRST

This is the reset signal for the serial interface to the SCC registers in the Juno r2 SoC. It resets the SCC
registers to their default values. It also resets the IOFPGA peripherals and the clock generators on the
V2M-Juno r2 motherboard.

2.6.3 

Reset sequence

The following figure shows the reset and configuration timing sequence.

MCC
reset

MCC

config

nPBRESET

Hard Reset

ON/OFF

Soft Reset

CB_VRAMP

All

PSUs

ON

MB

IOFPGA

OSCCLKs

SCCs

DB

FPGAs

OSCCLKs

SCCs

SCP

boot

IOFPGA_nRST

CFG_nRST

CB_nPOR

(nPORESET)

CB_nRST

CB_nTRST

ADP

boot

System
running

Warm

reset

ATXON

CB_CFGnRST

DCC

config

Figure 2-7  V2M-Juno r2 motherboard reset and configuration timing cycle

2 Hardware Description

2.6 Resets

ARM 100114_0200_03_en

Copyright © 2015–2017 ARM Limited or its affiliates. All rights reserved.

2-37

Non-Confidential

Содержание V2M-Juno r2























































































































































Отзывы:

Нет отзывов