ARM Musca-S1 Скачать руководство пользователя страница 77

Страница: 77 / 194

Table 3-18 APBNSPPCEXP0 Register bit assignments

Bits

Name

Function

[31:3]

Reserved.

[2]

NS_MRAM_MPC

Defines the security access setting for the
eMRAM

Memory Protection Controller

(MPC):

0b0

: Secure access only.

0b1

:Secure and Non

‑

secure access.

Reset value

0b0

[1]

NS_SRAM_MPC

Defines the security access setting for the
Code SRAM MPC:

0b0

: Secure access only.

0b1

: Secure and Non

‑

secure access.

Reset value

0b0

[0]

NS_QSPI_MPC

Defines the security access setting for the
QSPI MPC:

0b0

: Secure access only.

0b1

: Secure and Non

‑

secure access.

Reset value

0b0

APBNSPPCEXP1 Register

The Expansion 1 Non-secure Access APB slave Peripheral Protection Control Register characteristics
are:

Purpose

Defines the security access settings for the associated APB slave

Peripheral Protection

Controllers

(PPCs) outside the SSE-200 subsystem.

See the

Arm

CoreLink

™

SSE

‑

200 Subsystem for Embedded Technical Reference Manual (r1p0)

for more information.

Usage constraints

There are no usage constraints.

Memory offset and full register reset value

See

3.4.6 Secure Privilege Control Block

on page 3-66

The following table shows the bit assignments of the APBNSPPCEXP1 Register.

3 Programmers model

3.4 Base element

101835_0000_01_en

reserved.

3-77

Non-Confidential

Содержание Musca-S1


































































































































































































Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды

ARM Musca-S1, Техническое справочное руководство

Результаты поиска

Содержание Musca-S1

Отзывы:

Похожие инструкции для Musca-S1

Бренды по названию

Популярные бренды