ARM ARM9TDMI Скачать руководство пользователя | Manualshive

Страница: 85 / 154

background image

Debug Support

ARM DDI0145B

Copyright © 1998, 1999 ARM Limited. All rights reserved.

5-31

After the system speed instructions have been scanned into the instruction data bus and
clocked into the pipeline, the RESTART instruction must be loaded into the TAP
controller. This will cause the ARM9TDMI automatically to resynchronize back to

GCLK

when the TAP controller enters RUN-TEST/IDLE state, and execute the

instruction at system speed. Debug state will be reentered once the instruction
completes execution, when the processor will switch itself back to the internally
generated

DCLK

. When the instruction has completed,

DBGACK

will be HIGH. At

this point INTEST can be selected in the TAP controller, and debugging can resume.

To determine whether a system speed instruction has completed, the debugger must
look at SYSCOMP (bit 3 of the Debug status register). To access memory, the
ARM9TDMI must access memory through the data data bus interface, as this access
may be stalled indefinitely by

nWAIT

. Therefore, the only way to determine whether

the memory access has completed is to examine the SYSCOMP bit. When this bit is
HIGH the instruction has completed.

By the use of system speed load multiples and debug store multiples, the state of the
system memory can be passed to the debug host.

5.10.3

Instructions which may have the SYSSPEED bit set

The only valid instructions on which to set this bit are:

•

loads

•

stores

•

load multiple

•

store multiple.

When the ARM9TDMI returns to debug state after a system speed access, the
SYSSPEED bit is set HIGH.

«
...
83
84
85
86
87
...
»

Содержание ARM9TDMI



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM9TDMI

Бренд: Paradyne Страницы: 16

Бренд: Rane Страницы: 4

Бренд: EMCIS Страницы: 14

Бренд: H3C Страницы: 9

Бренд: ebm-papst Страницы: 13

COM Express conga-TC87

Бренд: Congatec Страницы: 114

Бренд: Pilz Страницы: 12

STEVAL-SCR002V1

Бренд: ST Страницы: 28

Бренд: Hama Страницы: 10

Бренд: ebm-papst Страницы: 13

55PUS8118 SCSI-2

Бренд: IBM Страницы: 42

Бренд: Fujitsu Страницы: 7

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 32

Бренд: Fujitsu Страницы: 6

FMC-16FX FAMILY ADA-16FX-ETHERNET

Бренд: Fujitsu Страницы: 14

Бренд: Fujitsu Страницы: 15

Бренд: Fujitsu Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды