ARM ARM9TDMI Скачать руководство пользователя | Manualshive

Страница: 42 / 154

background image

ARM9TDMI Coprocessor Interface

4-6

Copyright © 1998, 1999 ARM Limited. All rights reserved.

ARM DDI0145B

If a coprocessor instruction busy-waits,

PASS

is asserted on every cycle until the

coprocessor instruction is executed. If an interrupt occurs during busy-waiting,

PASS

is

driven LOW, and the coprocessor will stop execution of the coprocessor instruction.

A further output,

LATECANCEL

, is used to cancel a coprocessor instruction when the

instruction preceding it caused a data abort. This is valid on the rising edge of

GCLK

on the cycle that follows the first execute cycle of the coprocessor instructions. This is
the only cycle in which

LATECANCEL

can be asserted.

On the falling edge of the clock, the ARM9TDMI processor core examines the
coprocessor handshake signals

CHSD[1:0]

or

CHSE[1:0]

:

•

If a new instruction is entering the execute stage in the next cycle, it examines

CHSD[1:0]

.

•

If the currently executing coprocessor instruction requires another execute cycle,
it examines

CHSE[1:0]

.

The handshake signals encode one of four states:

ABSENT

If there is no coprocessor attached that can execute the coprocessor
instruction, the handshake signals indicate the ABSENT state. In this
case, the ARM9TDMI processor core takes the undefined instruction
trap.

WAIT

If there is a coprocessor attached that can handle the instruction, but not
immediately, the coprocessor handshake signals are driven to indicate
that the ARM9TDMI processor core should stall until the coprocessor
can catch up. This is known as the

busy-wait

condition. In this case, the

ARM9TDMI processor core loops in an idle state waiting for

CHSE[1:0]

to be driven to another state, or for an interrupt to occur.

If

CHSE[1:0]

changes to ABSENT, the undefined instruction trap will be

taken.

If

CHSE[1:0]

changes to GO or LAST, the instruction will proceed as

described below.

If an interrupt occurs, the ARM9TDMI processor core is forced out of the
busy-wait state. This is indicated to the coprocessor by the

PASS

signal

going LOW. The instruction will be restarted at a later date and so the
coprocessor must not commit to the instruction (it must not change any
of the coprocessor’s state) until it has seen

PASS

HIGH, when the

handshake signals indicate the GO or LAST condition.

GO

The GO state indicates that the coprocessor can execute the instruction
immediately, and that it requires another cycle of execution. Both the
ARM9TDMI processor core and the coprocessor must also consider the

«
...
40
41
42
43
44
...
»

Содержание ARM9TDMI



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM9TDMI

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

iTRON B 70.2040

Бренд: JUMO Страницы: 41

Бренд: Teletronics International Страницы: 57

Бренд: ZALMAN Страницы: 7

Бренд: Aaeon Страницы: 72

IPS Pro-Module-24C-GE-BP-TM

Бренд: Trend Micro Страницы: 3

Бренд: Gearlinx Страницы: 23

Бренд: Altera Страницы: 33

Бренд: Xilinx Страницы: 27

Бренд: Corsair Страницы: 10

Бренд: NetBurner Страницы: 30

SATA II-150 PCI

Бренд: SIIG Страницы: 16

Бренд: El.Mo Страницы: 16

Бренд: Behringer Страницы: 15

Бренд: CAME Страницы: 14

Бренд: Altronix Страницы: 8

Compressor DW-CP04

Бренд: Digital Watchdog Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды