ARM ARM946E-S Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 189

background image

Programmer’s Model

2-28

Copyright © ARM Limited 2000. All rights reserved.

You must align the region base to an area size boundary, where the area size is defined
in its respective protection region register. The behavior is unpredictable if this is not
done.

The instruction tightly-coupled memory base address is fixed at

0x00000

. For the

instruction tightly-coupled memory, the region base returns the value

0x00000

when

read.

When writing to the instruction tightly-coupled memory, you must set the region base
to

0x00000

. Writes with the region base set to any other value are unpredictable.

At reset, the region base for both the instruction and data tightly-coupled memory
region registers are cleared to

0x00000

.

At reset, the area size for the instruction and data tightly-coupled memory region
registers takes the value defined in the tightly-coupled memory size register (see
Register 0, Tightly-coupled memory size register on page 2-9).

You must program the data tightly-coupled memory region registers before you set the
data RAM enable bit (bit 16) in register 1 (see Register 1, Control register on
page 2-11). If this is not done, the data tightly-coupled memory resides at the same
location resulting in unpredictable behavior.

Note

If the data tightly-coupled memory is located at the same address as the instruction
tightly-coupled memory, then the instruction memory takes precedence for data
accesses.

If the data tightly-coupled memory is located at the same address as the instruction
tightly-coupled memory, and the instruction RAM is in load mode, data accesses read
from the data RAM and write to the instruction RAM.

2.3.13

Register 13, Trace process identifier register

This register allows you to identify the currently executing process in multi-tasking
environments using the real-time trace tools.

The contents of this register are replicated on the ETMPROCID pins of the
ARM946E-S.

The following ARM instructions are used for accessing the Process ID register:

MRC p15, 0, rd, c13, c1, 1; read process ID register

MCR p15, 0, rd, c13, c1, 1; write process ID register

«
...
46
47
48
49
50
...
»

Содержание ARM946E-S






























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM946E-S

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

Бренд: Intel Страницы: 108

Бренд: Digitus Страницы: 8

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: UNA AUTOMATION Страницы: 20

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

Бренд: Idis Страницы: 17

Бренд: AMX Страницы: 1

Бренд: Navitar Страницы: 1

Бренд: Beckhoff Страницы: 84

Broadband 700 MHz

Бренд: Alcatel-Lucent Страницы: 8

BNC-08DI, BNC-16DI, BNC-16SE

Бренд: Omega Engineering Страницы: 25

Бренд: LinMot Страницы: 62

Бренд: Curtiss-Wright Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды