manualshive.com logo in svg

ARM ARM946E-S, Техническое справочное руководство, Страница: 34 / 189

Поделиться
Скачать
ARM ARM946E-S Скачать руководство пользователя страница 34

Programmer’s Model

2-14

Copyright © ARM Limited 2000. All rights reserved.

ARM DDI 0155A

Bit 13, Alternate vectors select

This bit controls the base address used for the exception vectors. 

When LOW, the base address for the exception vectors is 

0x00000000

. When HIGH, 

the base address is 

0xFFFF0000

.

Note

This bit is initialized either HIGH or LOW during system reset, depending on the value 
of the input pin, VINITHI. This allows you to define the exception vector location 
during reset to suit the boot mechanism of the application. You can then reprogram this 
bit as required following system reset.

Bit 12, ICache enable

Controls the behavior of the ICache. 

To use the instruction cache, both the protection unit enable bit (bit 0) and the ICache 
enable bit must be HIGH. This can be done with a single write to register 1.

At reset this bit is cleared.

Bit 7, Endian

Selects the endian configuration of the ARM946E-S. When this bit is HIGH, big-endian 
configuration is selected. When LOW, little-endian configuration is selected. 

At reset this bit is cleared.

Bit 2, DCache enable

This bit controls the behavior of the DCache.

To use the data cache, both the protection unit enable bit (bit 0) and the DCache enable 
bit must be HIGH. This can be done with a single write to register 1.

At reset this bit is cleared.

Bit 0, Protection unit enable

This bit controls the operation of the ARM946E-S protection unit.

At reset this bit is cleared. This disables the protection unit, and as a result disables the 
instruction and data caches and the write buffer.

Содержание ARM946E-S






























































































































































































Отзывы:

Нет отзывов