Instruction Manual
5
6
Timer Button
Press the Timer button repeatedly to obtain the desired operating time (0.5 Hour to 8.0 Hours).
Each time the button is pressed the time interval is incremented by 0.5Hrs and the corresponding
display panel will show. 0.5h
›
1h
›
1.5h
›
2h……
›
8.0h then back to 0.5h
The unit will shut off automatically when the set time has been reached.
Swing Button
Pressing the swing button once selects 30°head unit oscillation.
The swing angle can then be increased up to 360°or decreased to zero by pressing the + or –
buttons. Consecutive presses of the+ button increases the rotation angle as follows: 30°
›
60°
›
90°
›
135°
›
180°
›
360°
›
off
›
30°…and the graphic display will change accordingly.
Please note that on the 360° setting the fan head will rotate continuously in the same direction.
On all other settings the fan head will oscillate back and forth.
Pressing the swing button again (when the fan is operating in swing Mode) will turn off the swing
function.
Horizontal Fan Direction Adjustment
The starting position of the head unit can be adjusted by pressing and holding the buttons marked
‹‹
and
››
Vertical Fan Direction Adjustment
The vertical fan direction can be adjusted by gently pushing the assembled head unit (with grille)
forward or backward until the desired angle is obtained. Always switch off the fan before making
any adjustment.
Remote Control
The remote control handset requires a single
CR2032 (or equivalent) 3V battery. To install the
battery remove the battery tray as shown on the
rear of the handset.Insert the battery as per the
polarity shown. The remote control has the same
functions as the buttons on the control panel keypad.
To use the remote control make sure that the fan is
plugged into the mains supply, then point the handset
to the sensor located within the display panel above
the keypad and press the desired button. The remote
control operating range is up to 6 metres. Make sure that there is no
obstacle between the remote and the sensor.
Note: The unit incorporates an infra red sensor. Ensure that the handset is directed toward
the sensor within the display panel, otherwise the remote control will not function.
Care and Maintenance
1. Always disconnect the cord from the electrical outlet when cleaning your fan.
2. Light accumulated dust may be removed from the fan with a soft cloth or vacuum cleaner using
the dusting brush attachment.
3. Wipe the exterior surfaces of the fan occasionally with a cloth moistened (not dripping wet with
a mild soap solution. Dry the case thoroughly with a soft dry cloth before operating the fan.
4. Avoid the use of gasoline, benzine, thinner etc as they may result in damage to the fan.
5. Store the fan in a clean dry place when not in use.
Warning: Do not immerse the fan in water or allow water to drip into the interior of the fan
housing as this could create a fire or electric shock hazard.
Important! Please read these instructions carefully
Model APF360
Warranty
Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product (“you”) from a retailer that this
product will be free of defects in materials and workmanship for a period of 24 months from the date
of purchase; provided the product is not used other than for the purpose, or in a manner not within
the scope of the recommendations and limitations, specified by Arlec, is new and not damaged at
the time of purchase, has not been subjected to abuse, misuse, neglect or damage, has not been
modified or repaired without the approval of Arlec and has not been used for commercial purposes
(“Warranty”).
If you wish to claim on the Warranty, you must, at your own expense, return the product, and
provide proof of original purchase and your name, address and telephone number, to Arlec at the
address below or the retailer from whom you originally purchased the product within 24 months
from the date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may make on the Warranty in the above
manner and if, in Arlec’s reasonable opinion, the Warranty applies, Arlec will at its own option and
expense (or authorise the retailer to) replace the product with the same or similar product or repair
the product and return it to you or refund the price you paid for the product. Arlec will bear its own
expenses of doing those things, and you must bear any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relation to the
product to which the Warranty relates.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: (03) 9982 5111
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: [email protected]
CPIN002702
CPIN002702
360
˚
Oscillating
Pedestal
Fan
40cm
B
REEZE
Model
APF360
Voltage
220-240V a.c.
Frequency
50Hz
Power
65W
Noise Level
≤
55 dB
Standby Power
≤
0.5W
Technical Specifications
Remote Handset