manualshive.com logo in svg

Arkray SPOTCHEM EZ SP-4430, Руководство по эксплуатации, Страница: 121 / 139

Поделиться
Скачать
Arkray SPOTCHEM EZ SP-4430 Скачать руководство пользователя страница 121

C

5-04 ● SP-4430

4-2

毎日のお手入れ

Chapter 5 TROUBLESHOOTING

4-2-1

試験片テーブルのお手入れ

PR : Prozone error
L 1 : Large difference between the measured
and the displayed values of calibrator L.
H 1 : Large difference between the measured
and the displayed values of calibrator H.
L 2 : Large variations between the measured
values of calibrator L.
H 2 : Large variations between the measured
values of calibrator H.
LH  :  No  difference  between  the  measured
value  of  calibrator  L  and  that  of  calibrator
H.
( 1 〜 6 ) : Channel with an error.
The display is shown only in multi
calibration, and nothing is displayed in
single calibration.

The magnetic card was caught when

inserted.

The head of magnetic card reader is

dirty.

●

●

Insert the magnetic card again.

Clean the head of the magnetic

card reader.

●

●

E21

Description and error message

Conditions and causes

Remedy

Ｅ２１ Ｃａｒｄ ｍｉｓｒｅａｄ

■■■■■■■■■■■■

ＯＫ（ＥＮＴＥＲ）

Wrong magnetic card was used (a

calibration card was inserted when the

display showed Reagent Card reading

or vice-versa).

●

Insert a correct magnetic card.

●

E24

Ｅ２４ Ｗｒｏｎｇ ｃａｒｄ

■■■■■■■■■■■■

ＯＫ（ＥＮＴＥＲ）

The same stripe was inserted. 

●

Insert a different stripe.

●

E25

Ｅ２５ Ｗｒｏｎｇ ｓｔｒｉｐｅ

■■■■■■■■■■■■

ＯＫ（ＥＮＴＥＲ）

During calibration, the difference of the

measured value and the display of

calibrator is extremely large.

The variations of the measured values

are extremely large in calibration.

Calibrator L and H might be set

oppositely in calibration.

Incorrect adjustment of calibrator.

●

●

●

●

Perform measurement again.

●

E30

Ｅ３０ Ａｂｎｏｒｍａｌ ｄａｔａ

（Ｌ１

■■■■■■

３）

■

ＯＫ（ＥＮＴＥＲ）

Cuvette: when a curette is used for liquid
level detection.
CNTRFG: When a centrifuge vessel is used.

A sample vessel is misplaced.

There is no sample or an insufficient

amount of sample.

A centrifuge tube was used in

calibration by calibrator kit.

●

●

●

Set the sample correctly.

Confirm the amount of the sample.

Be sure to use cuvettes in

calibration by calibrator kit.

●

●

●

E17

Ｅ１７ Ｎｏ ｓａｍｐｌｅ

（ＣＮＴＲＦＧ

■■■

）

■

ＯＫ（ＥＮＴＥＲ）

Wear protective gloves in order to avoid exposure
to pathogenic microbes.

WARNING

Содержание SPOTCHEM EZ SP-4430












































































































































Отзывы:

Нет отзывов