background image

FCC Notice 

 

This device complies with Part 15 of FCC rules. 
Operation is subject to the following two 
conditions: (1) This device may not cause 
harmful interference, and (2) This device must 
accept any interference that may cause 
undesired operation. 
 
Changes or modifications not expressly 
approved by the party responsible for 
compliance could void the user’s authority to 
operate this device. 
 

FCC ID: MKARI60 

Save this information for future use. 

 
Date of purchase    _____/_____/_____ 
 
Place of purchase  ______________________ 
 
   

______________________ 

 
Invoice/Receipt #  _________________ 
 
Model Number 

 _________________ 

 
Production Code   _________________ 
 
Notes: 

 

SPECIAL NOTE ON RANGE 

 

The average reception range is approximately ½ mile (800 meters).  The actual reception 
range could be greater or less depending on the location and/or the presence of obstacles 
between the vehicle and the receiver.  The reception range can also be affected by the 
presence of strong electromagnetic interference from outside sources.  

a3 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Important Information 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 

 
 

 
 

 

 
 
 
 

 
 

 

 
 

 

Installation  

User’s Guide  

Tranceiver Information  

Optional Accessories  

Appendix 

Содержание Scorpio















Отзывы: