ATS1100/1105
➋
1 2 3 4
➌
SW2
1 2 3 4
A
B
SW1 Dip Switch
Rx
SD
SD
SD
SD
ON
ON
ON
ON
Tx
1
2
3
4
1
2
3
4
1
2
3
1
2
3
4
4
J2
RAS 1
RAS 2
RAS 3
RAS 4
SD
SD
SD
SD
ON
ON
ON
ON
A
T
S
30
00
/4
00
0 (
J1
0)
+
12
0
V
D
+
D
-
IN
O
U
T
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
RAS 5
RAS 6
RAS 7
RAS 8
J3
SD
SD
SD
SD
ON
ON
ON
ON
➊
➍
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
RAS 9
RAS 10
RAS 11
RAS 12
SD
SD
SD
SD
ON
ON
ON
ON
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4
RAS 13
RAS 14
RAS 15
RAS 16
English
8-Area LCD RAS
M
OUNTING THE UNIT
Attach the mounting box using screws. Secure the PCB with the screw
supllied. Secure the keypad cover with the screw supplied.
When a pry-off tamper is required, use a screw in the back of the keypad
(see figure A,
➍
).
C
ONNECTING THE KEYPAD TO A CONTROL PANEL
(
FIGURE
A)
➊
Refer to the control panel installation guide for instructions.
LED
S
(
SEE FIGURE
A)
RX
LED flashes to indicate polling data is being received on the system
databus from the ATS control panel. If the LED does not flash the
control panel is not operational or the databus is faulty (usually
cabling).
TX
LED flashes to indicate the arming station (RAS) is replying to polling
from the ATS control panel. If the RX (Rx0) LED flashes but the TX
(Tx0) LED does not, the arming station (RAS) is not programmed to
be polled in the control panel or is addressed incorrectly.
LED I
NDICATIONS ON KEYPAD
Area
8 red LED’s illuminate when area 1-8 (or 9-16) are armed.
Will blink (armed) or flash (disarmed) on alarm.
Mains
Green LED illuminates if 230 VAC mains power is available.
Alarm
Red LED illuminates on any alarm in an area assigned to the
keypad.
Fault
Yellow LED illuminates on fault’s in the system.
C
OMMS CONNECTIONS
(
FIGURE
A,
TERMINAL
J3)
+12
0V
Power supply. If the distance between the arming station and the
control panel does not exceed 100m, then the arming station can be
powered using the Comms + and – from the control panel. Otherwise
use AUX PWR from DGP’s or an auxiliary power supply.
D+
Data positive and data negative connection of the databus.
D -
Remote units can be up to 1.5 km from the ATS control panel.
IN
A request to exit button (normally open, momentary push-button
switch) can be connected across “IN” and “-“. When pressed, this
button controls the request to exit function.
OUT Open collector output, 50 mA maximum. It is the first output of
the output control group that is assigned to this arming station.
RAS
DIP SWITCH SETTINGS
(
FIGURE
A)
➋
SW1 dip switches
These are used to identify the RAS address. See figure B for settings.
➌
SW2 “A, B, C, Term”
These are used to terminate the databus and enable various other
functions, as described below:
SW2-1, A Area 9-16
OFF The 8-area LEDs display the status of areas 1 to 8.
ON
The 8-area LEDs display the status of areas 9 to 16.
SW2-2, B Keypad backlight
OFF The keyboard backlight times out.
ON
The keyboard backlight stays on continuously.
SW2-3, C Magnetic card format (ATS1105 only)
OFF ATS
format
ON Non-ATS
formats.
(e.g., credit cards, any cards with data on track 2).
SW2-4, TERM
OFF Not the last device on the databus.
ON
Terminates the databus if this RAS is the last device on the
databus. See also the ATS control panel’s installation guide.
R
EADERS
C
ONNECTIONS
(ATS1105
ONLY
)
(
FIGURE
A, J2)
+5 VDC supply and data connections for ATS magnetic card readers
(ATS1105 only).
1
D1/D Read data pulse / Wiegand D1 line
2
D0/C Read clock pulse / Wiegand D0 line
3 GND
(0V)
4 +5
VDC
5 +12
VDC
Additional functionality.
-
Adjust LCD contrast
By pressing the clear button at the same time with the arrow up or
arrow down key.
1
105066
г
.
Москва
,
ул
.
Спартаковская
,
д
.11,
корп
. 1,
тел
. (095) 787-33-42, (095) 937-90-57;
факс
(095) 937-90-55
