Ariens Sno-Thro Pro 32 Скачать руководство пользователя страница 1

Страница: 1 / 27

Quick Start Guide

Pro 32 Track 12V (926514 s/n 101 & up)

•

Step 1: Unfold Handlebar

•

Step 2: Install Discharge Chute

•

Step 3: Install Chute Control Assembly

•

Step 4: Install Discharge Chute Rod

•

Step 5: Install Remote Deflector Cable

•

Step 6: Connect Battery

•

Step 7: Check Function of Dual Handle Interlock

•

Step 8: Check Track Tension

•

Step 9: Adjust Skid Shoes

•

Step 10: Check Auger Gearcase Oil

•

Step 11: Check Engine Crankcase Oil

•

Step 12: Fill Engine Fuel Tank

•

Step 13: Start Engine

•

Step 14: Stop Engine

READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.

IMPORTANT:

READ OPERATOR’S MANUAL AND ENGINE MANUAL

THOROUGHLY AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES
BEFORE OPERATING.

Содержание Sno-Thro Pro 32




























Результаты поиска

Содержание Sno-Thro Pro 32

Отзывы:

Похожие инструкции для Sno-Thro Pro 32

Бренды по названию

Популярные бренды

Ariens Sno-Thro Pro 32, Быстрый старт

Результаты поиска

Содержание Sno-Thro Pro 32

Отзывы:

Похожие инструкции для Sno-Thro Pro 32

Бренды по названию

Популярные бренды